GM Electric Fuel pump?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 27, 2004
Threads
31
Messages
148
Location
Bay Area, CA
I'm looking for an electric fuel pump for my F-equipped truck, and a guy told me that there was an AC in line pump that looked like a big fuel filter that worked well for this application, and hides well (for security). Is anyone familiar with it, and know what brand and model years it is?
Thanks.
 
Wrong question to ask me as much trouble as I have had with electric pumps in the past year after going to a system that has to run them....WTF would you want to?
Butch
 
Look at the TBI equipped trucks. I have one of those in my 1988 K5 Blazer. If you were to get to the parts store just give them this spec.

Chevrolet
1988-1991
K1500 Blazer/Suburban/jimmy
5.7L(350) Fuel injected

You will need the filter kit to go along with it too.

Side note. the body styles stayed old school till 1991 in the blazers/suburbans/jimmys.
 
fr8train said:
Look at the TBI equipped trucks. I have one of those in my 1988 K5 Blazer. If you were to get to the parts store just give them this spec.
blazers/suburbans/jimmys.

OK, don't do this, way too much pressure for a carb, unless you got a pair of Holley Dominators on that F
You need the cheapest pump any parts store offers for a carbed F 4-7 PSI will do fine, but just replace the mech pump
Butch
 
fr8train said:
Look at the TBI equipped trucks. I have one of those in my 1988 K5 Blazer. If you were to get to the parts store just give them this spec.

Chevrolet
1988-1991
K1500 Blazer/Suburban/jimmy
5.7L(350) Fuel injected

You will need the filter kit to go along with it too.

Side note. the body styles stayed old school till 1991 in the blazers/suburbans/jimmys.


I think thay are in tank, not in line
Clay
 
I don't thing GM made an in-line electric low pressure fuel pump. Lots of aftermarket folks have. If you get one, get an extra. They don't like heat very much. You must also bypass your mechanical pump to use it or you can pump your engine full of fuel. Some kind of emergency cut out is also somewhat important. The last thing you need in a roll over is to have your electric pump running and spraying fuel all over the place.

The Toyota mechanical one is very reliable and works well.
 
GM did put an inline electric fuel pump on their 6.5 liter diesels which mounted on the frame rail just under the driver (which they called a "lift pump"). AC Delco has them for about $98 and Napa for about $70. I do not know if running gas in it would work or if there was a gas version but I do believe you would be in need of a regulator after the pump to drop down to ~4 psi rather than 15. Carter actually makes one of the more dependable aftermarket pumps (Holley pumps have an awful failure rate) and they make one which does not require a regulator.
 
I have a good mech pump, but was looking at an electric pump as a security feature, with a hidden switch. But come to think of it, I could do just as well with a petcock off the tank under the seat, or how about a solenoid valve?
 
IMO, your best security is a hidden switch to the coil....it cranks, but won't start. Quite a few spots up behind the dash to pop a hole and install something too...

I just installed a watercraft-type ignition/fuel pump kill switch last night...pull the red cord and it instantly disconnects from the switch and kills power. Remove the cord and use just the black tab in an underdash hidden situation...

SKU 578583 from doitbest.com, ~$20 delivered. This is the switch type required for UROC competition rigs.
 
I had what your looking for on my 45LV, hell I thought it was a fuel filter.

why do you want one? I took mine off.
 
napa has a $40 4 psi one that I've been using for over a year, mounted to one of the head bolts bypassing the mech. pump. I only consider it a temporary solution, it is not as reliable as a Toyota mechanical. I will eventually switch back to mechanical and keep the electric in the toolbox for emergencies.
 
woody said:
IMO, your best security is a hidden switch to the coil....it cranks, but won't start. Quite a few spots up behind the dash to pop a hole and install something too...

I just installed a watercraft-type ignition/fuel pump kill switch last night...pull the red cord and it instantly disconnects from the switch and kills power. Remove the cord and use just the black tab in an underdash hidden situation...

SKU 578583 from doitbest.com, ~$20 delivered. This is the switch type required for UROC competition rigs.

Ya but you did not put that in for anti-theft, come on admit it you put that in so next time you roll it and fall out your truck does not drive away. After all it beats that suffers leg leash you used to use from you left ankle to your roll cage.

Back to the topic, GreenWeenie’s Dad put a small kill switch inside the cigarette lighter. You just pulled out the lighter part and with your finger could flip the switch. I have seen a few others that used relays and a combination of OEM switches. Using this system you have to say turn on the hi beams for the start relay to work. This makes for a clean set up that no one can easily figure out.

If your anti-theft is defeating the hot lead to the coil keep in mind especially with a 40 and no hood lock; it takes 2’ of wire to energize the coil and a screwdriver across the terminals on the starter to start the motor. Where as Jim45 is talking about taking away the fuel, truck no go. I would go with an inline solenoid to shut the fuel off. If you do remember you can start the truck and probably drive a few blocks before it starves.

Personally my 79’ needs 45PSI of fuel that one is easy to disable. My stock 78… well that’s the one I keep thinking I need to chain down.

Mark
 
Texican said:
OK, don't do this, way too much pressure for a carb, unless you got a pair of Holley Dominators on that F
You need the cheapest pump any parts store offers for a carbed F 4-7 PSI will do fine, but just replace the mech pump
Butch



Youre right dont do that one. Sorry man, keep forgetting that I am running a small block that uses an aeromotive regulator. Its the intank style that I switched to that keeps my fuel flowing with no starvation under load or fast accel.
 
Back
Top Bottom