Gear dilemma

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 8, 2004
Threads
70
Messages
343
Made a decision, still not sure about it.

1997 FZJ80, currently on OME J's w/315 Mud TA's, stock gears.

Ordered...Slee 6" and 36x12.50x16 TSL radials.

4:88's will turn 36" Swampers, RPM's similar to stock, better highway. Maybe.

5:29's will turn 36" for sure, RPM's lower than stock, better offroad. Maybe.

Will I go larger than 36's someday? Who knows? Will I go smaller? No.

The Cruiser will always see more highway than trails, nothing's close anymore.

Who's run 36's with 5:29's or 4:88's?
 
I am thinking about the re-gear thing myself ( i want to run 35s) have you priced 4.88s ? who retails them?
 
FWIW I run 36" TSL/SX in the woods and 33" ATs on the street with 4.56 gears. Swampers are hard to turn regardless of your gearing, but 4.88 sounds right to me. I wish I had gone that route sometimes, but the 33s on the street are just right.
 
that much highway, I would run the 4.88's and leave power mode on in the city.

It's about 3 hours or so to Uwharrie and about 6 or so to Tellico, depending. I'd rather drive my Cruiser to and from (utilitarian).

I'm trying to imagine 5:29's with 36" TSL radials and no carpet (durabaked inside) at 70 or so mph.

Also concerned about 5:29 durability compared to 4:88.

It seems a lot of 60 series folks run 4:88's with like 37's. Being 2F'd often.

Whereas more mini's with 4bangers/V6's run 5:29's for 35" and up.

And for some reason 5:29 seems to be the new "way to go" in 80's too with bigger than 35" meats?

Of course a better crawl factor would be good to go too. I don't "have" to drive the 80 everywhere, everyday.

Can't decide which is "better" suited.
 
It's about 3 hours or so to Uwharrie and about 6 or so to Tellico, depending. I'd rather drive my Cruiser to and from (utilitarian).

I'm trying to imagine 5:29's with 36" TSL radials and no carpet (durabaked inside) at 70 or so mph.

Also concerned about 5:29 durability compared to 4:88.

It seems a lot of 60 series folks run 4:88's with like 37's. Being 2F'd often.

Whereas more mini's with 4bangers/V6's run 5:29's for 35" and up.

And for some reason 5:29 seems to be the new "way to go" in 80's too with bigger than 35" meats?

Of course a better crawl factor would be good to go too. I don't "have" to drive the 80 everywhere, everyday.

Can't decide which is "better" suited.

I'm carpetless, 2nd/3rd rowless, and fully herculined in the interior and running 35's... the truck is LOUD indeed. You hear all of the engine noises, suspension noises, driveline noises, tires/road contact, exhaust (mine's full of craks and holes)....I did three layers of herculine inside of my rig and I am going to go thicker come spring. I am also going to soundproof the door panels as well, so hopefully that should help.

35's and 4.88 sound ideal to me.

I am not planning on going any higher with this rig (maybe 37's someday down the line).

The 80 is also not my DD. I use it sparingly. It sits most of the time....:princess:
 
I have a set of 4.88's in the garage waiting to be installed. Currently running 285's but will prolly go with Jon's setup or Q78-16 for trails and keep something in the 33 range for street (255's or 285's).

I was more than surprised to see how capable Jon's rig is running 36" TSX's with only a J lift and it sits lower than mine with the heavy kit.

Oh yeah... Jon good to see you're back, I know you were pissed two weeks ago.
 
I'd go 4.88. I wheel frequently and run 35's with stock gearing and it hasn't held me back anywhere. I leave the 'power button' on for the higher shift points. I'm real close to going 37's and then I will regear with 4.88's but not 5.29's. The truck drives to all trails. Doesn't get trailered anywhere.
 
It's all about the suspension droop. I removed (tore off) the rear sway bar. That really allows the rear axle to drop down. It made a big difference when in the rough and the truck still drives OK on the street.

I've considered that for a couple years then never do it for fear of my wife's driving. I worry enough as it is.
 
I am thinking about the re-gear thing myself ( i want to run 35s) have you priced 4.88s ? who retails them?

Who stocks them and who retails them is the question. Check out the vendor page, many retail the gears but I don't think many keep stock for long. The R&P are likely the same accross the board though, but prices vary.
 
I'd go 4.88. I wheel frequently and run 35's with stock gearing and it hasn't held me back anywhere. I leave the 'power button' on for the higher shift points. I'm real close to going 37's and then I will regear with 4.88's but not 5.29's. The truck drives to all trails. Doesn't get trailered anywhere.

That's what I'm leaning towards. Seems a lot of 60's with 37's go 4:88 too, with 2F's and 3FE's. 60's are the best relative comparison search I've pulled so far.
 
As far as the strength of the 5.29's christo had posted somewhere that he has broken several 4.88's but never a 5.29 set. There is also a thread where someone measured all of the teeth and contact points of the ring and pinion and that the argument is that the 5.29 is stronger if set up correctly..
 
I vote 5.29s, and if I weren't gonna be running 33's on the sreet, I would be going that route. I do plan on going 4.88s w/ 33 street and 38.5x11 trail. Lower t-case gearset is a high probability.

Yeah, I've been thinking about the Transfer Case too.

If my 80 only had a manual...
 
You're better off with an auto offroad gear wise, no slipping of a clutch, and your ratio is effectively lower with the torque converter slipping.

I'd go with the 5.29s, better offroad and better city, highways will have more pep you'll just have to drive a little slower (70 instead of 80).
 
As far as the strength of the 5.29's christo had posted somewhere that he has broken several 4.88's but never a 5.29 set. There is also a thread where someone measured all of the teeth and contact points of the ring and pinion and that the argument is that the 5.29 is stronger if set up correctly..



Setting up is another issue. I could do it myself, check, recheck, then check everything again. Or save my compulsive rechecking and let someone else install them and get it done faster.

With 5:29's I could leave the "power button" and overdrive button alone, especially when I'm in the mountains.
 
You're better off with an auto offroad gear wise, no slipping of a clutch, and your ratio is effectively lower with the torque converter slipping.

I'd go with the 5.29s, better offroad and better city, highways will have more pep you'll just have to drive a little slower (70 instead of 80).


I have noticed the transmission having a harder time turning the 315's with the 4:10's.

The thought of 38's and a sawzall has crossed my mind.
 
Go 5.29s, from all the testing I still think it is stronger gear than a 4.88...and you're gonna break other stuff before you break a gearset.

Also, I vote you get it professionally done. Less noise and a safer setup will be had if this is your first time installing gears (but sit and watch them do it!).

Yup, don't need to leave the power button on like you would probably end up doing with the 4.88s, and you still have even more power on tap by pushing the power button.
 
Back
Top Bottom