Gas Tank Lines???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 8, 2003
Threads
52
Messages
462
Location
Near Junk
I saw a pic before here on set-up for gas tank lines coming off the tank itself. I have a '76 40 with stock tank, de-smogged, weber carb and headers. No charcoal cannister either. There are three lines on the tank under the filler shroud. The pic I saw here showed how to cap off or route those lines. I assume I don't need a return line as I don't see it there.

Did some searching here this AM and no luck plus my PC keeps hanging during searches here???

Anyway - anyone know this or recall that thread with the tank line pic?

AndrewT
 
Someone else may chime in but,

On mine I just plugged off the 3 lines that go up by the filler for the emission vapor venting. The midsized one went on the small nipple of the filler neck for venting purposes. The red circled one one was the supply and the blue circled one was the return. At least as far as I can remember on my old setup.
Parts 072.webp
Parts 071.webp
z.webp
 
Never had any fumes or stinkyness in the cab on mine. It may have been a vented cap, I don't remember. But yeah as long as that main vent line is hooked up and working properly then you'll be alright.

If you plug everything off then yes you'll have probs.
 
HawkDriver said:
Never had any fumes or stinkyness in the cab on mine. It may have been a vented cap, I don't remember. But yeah as long as that main vent line is hooked up and working properly then you'll be alright.

What you refer to as the "main vent" is merely to vent air out of the tank to the filler neck when you are filling the tank with gas. It has nothing to do with venting the tank while the vehicle is in operation. As Pin Head (Hi, Charlie!) stated above, you need to hook up the actual tank vents. At least hook up one of them. Although you should have it vented through the charcoal cannister, you can run one of the lines to the height of the upper part of the firewall, and then to the frame rail. Put a cheap fuel filter inline to keep junk out of your gas tank. ;)
 
Vortec_Cruiser said:
What you refer to as the "main vent" is merely to vent air out of the tank to the filler neck when you are filling the tank with gas. It has nothing to do with venting the tank while the vehicle is in operation. As Pin Head (Hi, Charlie!) stated above, you need to hook up the actual tank vents. At least hook up one of them. Although you should have it vented through the charcoal cannister, you can run one of the lines to the height of the upper part of the firewall, and then to the frame rail. Put a cheap fuel filter inline to keep junk out of your gas tank. ;)

Ok. Question, how does the tank know the difference of whether it's in operation or just filling up? I thought with a vent cap it's just venting all the time. I havn't seen the internal routing, so I'll take your word for it. Still, that's how I ran it, the three lines plugged off, and had no operational problems and no fumes.

Thanks :D
 
The vent attached to the filler neck is to allow air to exit the tank through this breather, rather than trying to exit through the filler neck as gas is going in. It has no function other than this. In stock configuration, the tank does not have a vented cap. Installing a vented cap is asking for problems when the vehicle is side-hilled to the passenger side, and having a full tank of gas. The best configuration is a tank vented through the charcoal cannister, and having a non-vented cap, as it came from the factory.
 
Vortec_Cruiser said:
The vent attached to the filler neck is to allow air to exit the tank through this breather, rather than trying to exit through the filler neck as gas is going in. It has no function other than this. In stock configuration, the tank does not have a vented cap. Installing a vented cap is asking for problems when the vehicle is side-hilled to the passenger side, and having a full tank of gas. The best configuration is a tank vented through the charcoal cannister, and having a non-vented cap, as it came from the factory.

Aha,

;)
 
Vortec_Cruiser said:
What you refer to as the "main vent" is merely to vent air out of the tank to the filler neck when you are filling the tank with gas. It has nothing to do with venting the tank while the vehicle is in operation. As Pin Head (Hi, Charlie!) stated above, you need to hook up the actual tank vents. At least hook up one of them. Although you should have it vented through the charcoal cannister, you can run one of the lines to the height of the upper part of the firewall, and then to the frame rail. Put a cheap fuel filter inline to keep junk out of your gas tank. ;)

OK - I don't have the charcoal canister in the rig I bought. I have the 'main vent' (ie filler neck vent for the tank when you add gas) hooked up. On the other three lines (which are all in a row) - the two closest to the DS are looped back on each other (one tube connects to the two ports) and the third port is just a dangling line. I believe what you are saying here is that I need to atleast use that third line as a vent and I need to run it up some height above the tank. Since this is in the rear of the PS seat, can I run this line up and out the PS rear and attach to the frame rail there? Does the line have to be above the tank across its entire length?

AndrewT
 
I have same tank non veted cap and all lines plugged no vent for 2 years nom problems at all. When i did it i thought that i may need to get a vented cap but i have not. Maybe just run it plugged and see what happens. I was afraid of gas fumes. I used to have gas fumes from the old tank (its a 73) rusted pin holes in bottom of old tank. gas would evaporate before you would ever see it. It would smell though. I bought new tank from toyota and it was for a newer truck the 73's discontinued. Plugged all lines but the feed and no problems.
 
Back
Top Bottom