Front geometry problem????

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 21, 2008
Threads
6
Messages
95
I have a problem with a 6 " competition old man emu ,after racing my truck in a rally I broke my panhard rod once and broke the braket that goes to from the chassis to the panhard rod once also , my mechanic moved the panhard rod from the chassis side down and built a bullet proof bracket ( I retained the original panhard rod ) after these I grabbed the cruiser and did a 1800 mille trip , but the truck is not reliable , when I accelerate the body on the front of the truck moves towards the right and when I release the gas it comes to the original position , not good for a rally truck to have all these strange body moves, I was thinking it may have something to do with the steering geometry like the pitman that has to be lowered or something . I really need help with these issue, any kits available , any recomendations????
 
my mechanic moved the panhard rod from the chassis side down and built a bullet proof bracket

When your mechanic remounted the panhard rod, he moved it in a way that when the truck moves up and down, the panhard rod no longer has the same geometry as the drag link. You'll likely need to remount the panhard rod back to it's original location to solve this.
 
why not have him make a "bullet proof" bracket in the stock location, they sell "beefed up" panhard rods too. Should make for better body roll, sounds like yours has some serious roll....

Ryan
 
I had a problem after installing the same lift and a 2" body lift... the rig was all over the place when driving at speed,i eventially found the problem....the king pin inclination goes for a ball of:censor: as soon as you start lifting the rig .
You can replace the control arm bushings but that'll only correct a couple of degrees ....not enough to get the steering geometry back in spec.....i cut the control arm brackets off the diff housing, corrected the angle by turning the diff and re-welded the brackets after squaring it all up
IMGP1276.jpg

Good luck
 
the drag link and panhard need to be parallel to each other otherwise you will have bumpsteer when the axle/frame relationship changes, such as when body raising when accelerating or the axle flexing over rocks or in tight turns.

The caster could be off depending on how you corrected for it. But if you are at 6" of lift you'll need to go with something more than even caster plates alone can provide. A couple of guys have used my plates with OME bushings or a more tried and true fix would be Slee's arms.
 
Original Equipment bushings in the slee arms are probably the best option with a big lift like that.

LT's Plates work great with my front J springs.

If I were running in off road rally races I would have changed out the radius arm suspension. Probably would have fabbed in a 4 link leading arm suspension. If all 4 links are parallel you can use the stock drag link and panhard rods or better yet beefed up replacements so you dont need funky hydraulic cylinder steering.
 
Well the caster issue is fixed I custom made the braket that lower the front arms and have the caster corrector bushings , after that it was machined mesured and it was fine , my big consern if I put the panhard to the original place is the movement of the axel to the sides. Any solutions to the steering issues or just put the panhard on the stock location.

Ps Thanks to everybody that has put the 2 cents on the subject I appreciate.
 
Check your knuckle bearings if you have not yet. If you broke the panhard mount it must have been a heck of a jolt and got transfered thru the kingpin bearings..

The caster being off causes big steering issues. You probaly solve a bunch of it if the arm drop put caster back to stock.

Make sure the axle and frame mounting locations for the panhard are the same as stock. Then reinforce them.. Using the stock mouning locations will allow for the pahard and the drag link to have the same angle during suspension movement. Next get an adjustable panhard rod to adjust the axel so that it is cetered when the suspesion is at rest.
 
Back
Top Bottom