Front end clunk.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 31, 2007
Threads
43
Messages
187
There is a clunk in the front driver's side of my rig these days and I'm gonna begin diagnosing it.

What should I do to figure out what could be wrong? I have no previous SFA experiance to speak of.

Also is there a good writeup on doing the front bearings?
 
Possible shock or shock mount, possible loose swaybar-to-axle housing mount. Possible body mount (under driver's footwell) loose.






D-
 
All of the above and a loose caliper, dragging/stuck caliper on the DS, or non-functioning caliper on the PS (rare), lower tire pressure on the side it pulls to, or just about anything else loose up front.

Of course, it could be more than one problem, and it could be a quick fix ie: a loose shock causing the clunk, and low tire pressure on the DS front.
 
Best thing to do is get under it and starting checking for loose or missing nuts and bolts, etc. First I would look at the shocks for the clunk, unless it is a big clunk and you have recently run it into a ditch, then everything is on the table. After driving you could check the heat of the rotors, carefully, by hand; ie: is one smoking hot and other just normal hot? Not very scientific, but might help ie: if you see one rotor that looks glazed with darkish blue streaks, from excess heat, from dragging pads, etc. That would be the left front if it is pulling that direction.
 
I had similar issue like you mentioned in my last LX. Whenever I go over speed bumps in the parking lot, I heard clunk or a tiny grind. After I did the full front knuckle repack, and it goes away. Check your knuckle grease level, and maybe add a few squeezes in there???
 
Check out the bearings while you are in there... mine made noise but when I was turning and putting weight on it. More like a rumble though. But if you are taking it apart you might as well do the bearings while you are at it.
 
I finally crawled under there to take a look and found play in the lower DS shock mount, do I just tighten up the nut on there or is there more to it?

Also I found some play in the tortion bar mounts where it bolts to the axle, is this normal cause its the same on both sides?
 
I had a ckunky rattle type noise on bumps in the road, I checked everything under the car for tightness, it ended up being the parking brake shoes, I was advised to pull the prk brake up slightly while going over bumps, and it was not there!! I done a complete park brake ajustment and now its gone.
 
Supra...

You're in CO, Denver area, correct? Did this just start happening with the recent cold weather?

I ask because on Sunday I just noticed a "thunk", right under my left foot (DS footwell) when going over road imperfections, ruts, bumps, etc. I swear I can feel the thunk as well.

Haven't had any previous problems but it reminds me of the sound when the ball joints were going out in my old Durango. Hopefully this weekend I'll be able to get under there to see what the heck it might be.
 
Supra...

You're in CO, Denver area, correct? Did this just start happening with the recent cold weather?

Yea I live just outside Denver north about 1500 miles. You can probably see my appartment on the other side of the Canadian border on a clear day. LOL JK

Nah I live in central Canada and the problem started much less often about 4 months ago.
 
Yea I live just outside Denver north about 1500 miles. You can probably see my appartment on the other side of the Canadian border on a clear day. LOL JK

Nah I live in central Canada and the problem started much less often about 4 months ago.

Confused you with someone else obviously - We can see a LONG way from up here on a clear day but not quite that far :D

I was hoping your problem started with the cold weather like mine. It was warmer this evening on the drive home and no clunk for me at all :confused:. Suppose to be 40F around here by Sunday so I'll check it out then. If I find anything obvious I'll report back.
 
Best thing to do is get under it and starting checking for loose or missing nuts and bolts, etc. First I would look at the shocks for the clunk, unless it is a big clunk and you have recently run it into a ditch, then everything is on the table. After driving you could check the heat of the rotors, carefully, by hand; ie: is one smoking hot and other just normal hot? Not very scientific, but might help ie: if you see one rotor that looks glazed with darkish blue streaks, from excess heat, from dragging pads, etc. That would be the left front if it is pulling that direction.


Interesting, I just had my front brakes done - at Toyota Dealership - new OEM rotors and pads. A few days later I complained about excessive "squeal" (I park in a narrow parking garage so very noticable). Tech told me the new rotor (pad?) is glazed = bring it in, set up a time and fix no charge. Have them flush/bleed brakes while we're at it - surprised they will negotiate price within reason.
 
Back
Top Bottom