Front Axle Service needed?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 4, 2003
Threads
27
Messages
161
Location
Oxnard, CA
While checking the bolts on the new SROR sliders, found more grease on the driver's side than before:
WinterBreak2007-2008.jpg
.

Is an axle service in my near future? Also, the front rotors were replaced about 15,000 miles ago by the dealer and they replaced some axle seals- is the new leakage affected by the seals installed during a rotor replacement? I read through the axle service instructions in the FAQ but am still a little confused about which seals lead to what leakage.
 
IMO, that's not bad enough to justify a complete teardown and R&R of the front knuckles. I've seen much worse go for awhile. Maybe check the lube in the diff, see if it's goopy (use the fill hole). Squirt some grease into the knuckles via the little plug. Run it till it gets snotty on the outside.

The seals they likely replaced with the rotors are the hub seals, the go into the back of the front wheel hubs. The seals that usually go bad to cause contamination of the knuckle grease are the tube seals, much further in.
 
It's not the end of the world but ideally you'd want to do the front axle rebuild as a PM, every 60K miles, whether the knuckles are leaking or not. Any idea how many miles since yours were torn down?
 
Can you please post the seal part # from your Toyota receipt?

Well, pulled out the receipt for the brake replacement just under 15,000 miles ago, and no mention of a seal installed- but I remember the service advisor talking about having to replace some axle seals. I'll have to talk to the dealership about that one.

I found the receipt for the front end repack 24,500 miles ago (PO had this done at the same dealer), with items as follows:
"Replace front brake pads and grease seal, repacked bearings and machined front rotors"
"c/s leaking grease in front of vehicle both sides"
"Found front axle seal leaking into knuckles causing knuckle wipers to leak replaced axle seals and wipers or knuckle seals"
Parts listed:
2 90311-62001 Seal, type T oil (this listed under the brake service)
2 90310-35010 Seal, type S oil
2 43204-60031 seal sub-assembly, steer
2 4345-60020 gasket, knuckle spin

This seems to be something of a short list, is there a shortened repack procedure they might have followed instead of the full teardown?

So after looking at this, I'm thinking maybe this "type T" seal wasn't replaced when I had the rotors replaced, and perhaps it should have been. Could this be the cause for the new seepage miles later?

Thanks,

Brandon
 
I found the receipt for the front end repack 24,500 miles ago (PO had this done at the same dealer), with items as follows:
"Replace front brake pads and grease seal, repacked bearings and machined front rotors"
"c/s leaking grease in front of vehicle both sides"
"Found front axle seal leaking into knuckles causing knuckle wipers to leak replaced axle seals and wipers or knuckle seals"
Parts listed:
2 90311-62001 Seal, type T oil (this listed under the brake service)
These are the hub seals for the inner wheel bearings.

2 90310-35010 Seal, type S oil
These are the axle/tube seals. This is what you want to see.

2 43204-60031 seal sub-assembly, steer
These are wiper kits.

2 4345-60020 gasket, knuckle spin
These are spindle gaskets.
This seems to be something of a short list, is there a shortened repack procedure they might have followed instead of the full teardown?

It looks like what they did was to cure the leaks, not a full rebuild. I would say they did 98% of the tear down already at that point. They didn't replace the king pin bearings and dust seals.
 
Thanx, you guys are the bomb! I'll need to do mine too in the near future.


This is the most informative LC site on earth. Period!
 
Nothing about the looks of that knuckle would give me cause for concern. It's normal for some grease to accumulate there over time. Keep an eye on it over the next month or so. If you have a blown inner axle seal, the grease accumulation would get MUCH worse. There will be no question as that area will turn into a nasty goop of oily grease caked all over the area. There are probably some pictures of that scenario floating around here somewhere.

You should be able stick your head up behind the wheel and look in the grease plug hole to see what the consistancy of the grease is looking like in the knuckle cavity. Don't forget to add grease through the plug hole every 5 to 7.5k. but don't over fill :D.

:beer:
Rookie2
 
How do you know when to stop filling the knuckles? What will overfilling do?


What kind of grease do you recommend!

Mine look dry, however I will have Slee do my front axle service this month, should I be concern? I will be traveling 800 miles to take care of the service!
 
Back
Top Bottom