Found my weird handling issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

CreeperSleeper

Cascade Cruisers
SILVER Star
Joined
May 16, 2005
Threads
182
Messages
7,482
Location
Canby, OR
Well, I was driving home from getting my exhaust done and I couldn't keep the poor 80 going in a straight line. I was absolutely everywhere... Now my truck isn't the best handling thing in the world due to a combo of a bent rear panhard, no balancing weight on the wheels, bent tie-rod, shot TRE and no castor correction (I know, I know... I'm a :hillbilly:) but this was unbelievable!:confused:

Well, I got it into the garage and stared at it for a couple of days... Then I noticed this:
P3160116.jpg

:hhmm:
Now, I just resealed these axles in October when I went to Longs... I look closer and realize that the fluid is NOT 90w.
P3160115.jpg

:doh:
I pull the tire off and realize that I can move the knuckle 1/2" up and down and almost a full inch side to side. :eek: "Hmmm... That's not right" I look underneath and this is what I saw:
P3160117.jpg

:bang:
As far as I know, Christo and I are the only people to acomplish this on an 80... I know it happens on mini-trucks with Hi-Steer, but stock steering on an 80?!? Anywho, so once again, my front axle is being torn apart... This time all of the bearings will be replaced instead of just repacked and all of the studs will be upgraded to ARP. While I'm in there, I might as well get those 5.29's in. *sigh* Looks like Jillian will be down for about a month so I can save up the cash. Oh well, I'll just wheel my wifes 4Runner meantime! :idea::steer:
 
How does that happen?

On mini-trucks with aftermarket steering arms, it's usually because the nuts start to back off, causing some slop. The slop with then sheer the studs when you need them the most. As far as mine, I have no idea. Checking that those nuts are tight is part of my pre-flight checklist...
 
Checking that those nuts are tight is part of my pre-flight checklist...

The rest of Chad's pre-flight checklist:

• Highlift jack handle duct-taped to TRE's? Check.
• Bungee cord still holding battery down? Check.
• Radiator bailing wire still holding? Check.
• Zip ties still holding engine and trans together? Check.
• Front fender pulled out far enough to not rub front tire? Close enough.
• ABS and rev-limiter disabled? Check.
• Castor within spec. ±20°? Check


:)
 
How does that happen?

It happens because the nuts loosen up and allows play in the steering arm. Eventually the slight movement cause fatigue in the stud and it sheers.

I have sheered knuckle studs in my FJ40 in both stock configuration and after I went high-steer. I have found loosened nuts, cone washers and a loose stud in my FZJ80 before it ever saw any trail time. As creeper said, I always check the torque on those nuts before and during any trail ride. I have torqued them at the beginning of the Rubicon and found them loose again half way through the trail.

Now I locktight the nuts.
 
The rest of Chad's pre-flight checklist:

• Highlift jack handle duct-taped to TRE's? Check.
• Bungee cord still holding battery down? Check.
• Radiator bailing wire still holding? Check.
• Zip ties still holding engine and trans together? Check.
• Front fender pulled out far enough to not rub front tire? Close enough.
• ABS and rev-limiter disabled? Check.
• Castor within spec. ±20°? Check


:)

Cute! And you still follow me on the trail...:flipoff2:
 
Other then the birf soup, what am I looking at here? Is that a cracked steering arm?
cracked_arm.webp
 
Is jillian your wife or cruiser?
 
This time all of the bearings will be replaced instead of just repacked and all of the studs will be upgraded to ARP.

I suppose addressing the symptoms is one approach.

I personally would attack the problems

bent rear panhard, no balancing weight on the wheels, bent tie-rod, shot TRE and no castor correction
 
I suppose addressing the symptoms is one approach.

I personally would attack the problems

What problems? :flipoff2: The TRE and tie-rod are being replaced at the same time as I finally got them built. The panhard bar should be coming in May. As for running no weights on the tires, I never do. They make things worse after wheeling at low pressure and the tire spins on the wheel... As for the castor correction, I don't see that as a problem at all...:cheers:
 
One of our local members had this happen. It's caused by lose studs when you pull the steering arm off during a birfield repack. If you do a repack and want to pull the steering arm I highly recommend replacing the studs or ensuring the original ones are tight. Otherwise DON'T pull the steering arm off, just pop the tie rod ends off.
 
Yeah, I have no idea why mine failed. Like I said, it's something I check regularly and they have never been loose... However, I have noticed that the retaining rings on the back of the knuckle were backwards. Again, I never removed the knuckles on my 80, so it's been into before... I wonder if the PO didn't tighten the stud all the way and I've been checking the nuts thinking all is good.
 
Yeah, I have no idea why mine failed. Like I said, it's something I check regularly and they have never been loose... However, I have noticed that the retaining rings on the back of the knuckle were backwards. Again, I never removed the knuckles on my 80, so it's been into before... I wonder if the PO didn't tighten the stud all the way and I've been checking the nuts thinking all is good.

Maybe so. If just one stud was compromised and not fully tight when the nut went on it could have lead to this. The member locally here that had that happen also never touched the bir's except for the previous owner and that would have been a few years and several thousand miles prior (maybe 30ish).
 
Back
Top Bottom