for those that need reminding...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

i wore out one of those wire wheels removing surface rust from the floor of my piggy, so i bought a newy, but it'd only fit on the 9" grinder because of the thread size, which worked great, but beware if using one on a 9" as the torque is huge in comparison to 4". mine grabbed on the door edge and kicked into my leg, lucky for me i was wearing tough old jeans and not shorts.

sometimes you can't avoid using bondo, i'll admit i use it, but only for finishing, not creating a whole new panel or filling a huge crater. i've seen one 55 with a layer of bondo on one of the front quarters that had actually started to lift away, LOL it had two panels, needless to say i didn't end up buying that cruiser.
 
Sorry..

but all these bondo stories got me all nostalgic and I have to tell my own.

I had bought a freshly repainted '74 Cruiser in 1989 from a co-worker/friend. He absolutely swore the only bondo was in a little spot on the right rear quarter panel.

Three years later, on my first Rubicon trip, drivers front tire was catching the inner lip of the fender, bending it down. Tire carnage was sure to follow. So I decided to bend the fender up out of the way, using a hi-lift jack. As the fender returned to it's original location, a popping sound created a pink UFO. Yep, I had this 5" diameter pink pancake pop off the top of the fender and land on the rocks nearby.

Even when shown the proof (pink on one side, pretty metallic grown on the other), the PO insisted that there wasn't any bondo on the fender. :mad:

I'm using a magnet next used vehicle I buy, where the seller swears there's no body filler on it!
 
Bondo Is your friend

Plastic body filler is a Must when trying to get a body straight.........BUT it should not EVER excede 1/4 inch. One huge key to making it stay is to weld in new metal and weld old holes up. If moisture gets to filler, your going have problems. You should always use a high quality sealer over finished body filler and primer. On the subject of fiberglass for body repair I don't and won't do it. It is only a short term used car lot fix.

follow these steps

1. grind or cut out rust
2. weld in new metal
3. fill with high quality body filler
4. sand
5. prime with a high build primer
6. sand
7. seal with 2 part epoxy sealer
8. paint
9. OR smear with cheap bondo. Rattle can it. Tear it up in the woods, and repeat

Always remember when it comes down to it my advise ain't worth doodly squat :cheers:
 
So, here’s an account of day number two with my first cruiser.

Taking some random piece of advise my father gave me some years ago, I took a magnet when I first looked at the prospective cruiser. I was of the high power variety and was about 3/8 of an inch in diameter and I believe its original use was in a hard drive a fried a few years earlier and it has stuck on the side of my red craftsman tool box ever since.

Anyway, it didn’t take a rocket scientist to see the cruiser I was looking at had some bondo on the passenger rear quarter. I new it wasn’t that bad, and from what I was able to tell with the magnet the rest of the cruiser was pretty strength and no bondo. When I got home, I parked it and I went to sleep thinking of everything I could do to my cruiser–starting with removing the bondo that was flaking and peeling off.

The next day I began the operation. I used a wire wheel and a 4 inch grinder. I was surprised to see how much I could get off in such a short amount of time. I also noticed an occasional pinching feeling on my arm. I noticed some of the wires from the wire wheel were coming off and I was thankful during this procedure I had safety glasses. When I was finished, I noticed some of the wires from the wheel on my pants, on the ground and on my arms. I didn’t really think to much of it until a few hours later when I finished up a few other things and decided to take a break. When I sat down on the stool I have in my garage, I felt a surge of pain never felt before. A pain that resulted in a scream scaring even the most hardcore Guns and Roses fans back in the huge arena tours in the 80's. A scream that would the god of 80's screamers--Axle Rose himself.

One of the wires from the wire wheel had came out and ended up sticking in my pants. When I sat down, there was full penetration of the wire in to my scrotum, and by the feel of it, it seemed like it went in about ½ and inch.

Be careful when using a wire wheel to remove bondo or any other material. Check your pants. No joke.
 
I tried the 3" scotchbrite discs on my die grinder to get the bondo off of my HJ and they seemed to hold up pretty well. Didn't clog up. I am gonna try them on the roof of my fj60 soon. :eek:
 
BushBoy said:
i wore out one of those wire wheels removing surface rust from the floor of my piggy, so i bought a newy, but it'd only fit on the 9" grinder because of the thread size, which worked great, but beware if using one on a 9" as the torque is huge in comparison to 4". mine grabbed on the door edge and kicked into my leg, lucky for me i was wearing tough old jeans and not shorts.
t


yeah, watch out.I was wearing shorts useing one of these to clean up my 55 springs when I had the pack apart.Well I had the last lil bit to go, it was like 95 degrees out, I had been up way to long and had a couple beers in my head.I turned to look a something with my finger off the triger.Sitting indian style wasn't the best idea I guess. Vroompf.It had not came to a complete stop just yet.I look down and there is a real nice clean spot.The spings where off a Michigan cruiser so I was covered in cancer dust.Only took 3 weeks to heal up tho.Not bad being the scare is about 3 1/2L x 1W (inches) and bout 3/8 thick.
 
Hi All:

Yep, I can relate to all these "bondo" posts - I completely agree with "DesertDave" - the next FJ40 I buy will have been throughly inspected with a magnet, flashlight, and long screwdriver on *all* surfaces!

You see, I had to do a 2/3rds body tub swap on my FJ40 because there was so much body rot covered in bondo!

I do have a *little bit* of bondo on the replacement body tub, but only as shallow filler before painting on a couple of spots!

Good luck with your FJ55 Ige!

Regards,

Alan
Seattle
 
Back
Top Bottom