Southeast Overland
Get lost! Go explore!
thanks malphrus - I sent a PM
For Sale / Wanted To Buy (2 Viewers)
- Thread starter ClemsonCruiser
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Hey, thought i would try here also.
Am looking for a project trail 40.
Just really need frame / tub / front and rear ends.
And the tub can have some rust as most do.
Thanks all of my southern brothers.
Am looking for a project trail 40.
Just really need frame / tub / front and rear ends.
And the tub can have some rust as most do.
Thanks all of my southern brothers.
Hey Krazy I have a front cowl free for the taking.....it's got the windshield frame on it too. It's in decent shape the only major rust is the floor below the pedals. But it's got knobs on it and the pedals. It's from an older 40 but you're more than welcome to come and look at it. I can take some pics and email it to ya if you're interested. I also have some other parts too. Good luck
I wish i would of known that before i rebuilt my 45. I could of used that so i would not of had to put a different type of dash / guages in it.
I will keep you in mind though.
I will keep you in mind though.
mmcinnis
Supporting Vendor
I'm looking for a set of factory seats(front) 81 fj 40. Coming up to the cook out in July with jimbo. Will pick up then.
Thanks. Mike
Thanks. Mike
FJ 40 fenders
need a good set of fenders. I am in atlanta, ga. I can pick up or get one of the atlanta members to pick up at a upstate event
contact is keilthompson@yahoo.com or 404-642-1207
need a good set of fenders. I am in atlanta, ga. I can pick up or get one of the atlanta members to pick up at a upstate event
contact is keilthompson@yahoo.com or 404-642-1207
Last edited by a moderator:
I posted a few hard tops for sale. They can be delivered to the UC BBQ in a couple of weeks. Let me know if there is any interest.
-Todd
https://forum.ih8mud.com/showthread.php?t=164152
-Todd
https://forum.ih8mud.com/showthread.php?t=164152
Hey Todd you don't by chance have a used rain gutter sittin around do ya? Mine was rusted out when I bought my 40...mostly run the soft top but may put the hard top on everyonce and a while....thanks, Chuck
The gutters I have are all attached to the tops still. It would probably be easiest to just switch out fiberglass. I've heard those pop rivets are a nightmare. If I have to start selling the tops off as pieces I let you know. I'm trying to get some cash together for a Pakistan top and clear off my back patio for the misses. These land cruiser tops really look nice around the pool/patio when we have guests over.
Anyone interested in a 2F, 4-speed or split case from the '86 FJ60?
the truck has 261k on the clock but I don't know the history.
2F: complete with all smog and a/c compressor(might not work). powersteering pump and alt may or may not be included. one cyl (#4) supposedly has low compression (105) and I will try to confirm that if some one has a compression tester i can borrow.
H42: There is a little bit of noise coming from the input bearing only noticable at idle but it shifts and drives well.
Split T-Case: good as far as I know.
Over all they run/drive great! just got back from a 3,200 mile trip with no problems and it's currently my driver.
I will be pulling them out in a week or so. Prices to be determined. If anyone is interested, the cruiser will be availble to test drive at the BBQ this weekend before I pull the powertrain. let me know!
prices posted...https://forum.ih8mud.com/showthread.php?t=165722
the truck has 261k on the clock but I don't know the history.
2F: complete with all smog and a/c compressor(might not work). powersteering pump and alt may or may not be included. one cyl (#4) supposedly has low compression (105) and I will try to confirm that if some one has a compression tester i can borrow.
H42: There is a little bit of noise coming from the input bearing only noticable at idle but it shifts and drives well.
Split T-Case: good as far as I know.
Over all they run/drive great! just got back from a 3,200 mile trip with no problems and it's currently my driver.
I will be pulling them out in a week or so. Prices to be determined. If anyone is interested, the cruiser will be availble to test drive at the BBQ this weekend before I pull the powertrain. let me know!
prices posted...https://forum.ih8mud.com/showthread.php?t=165722
Last edited:
I am selling a '78 rolling chassis. Frame has new rear gussett and "bumper" crossmember. Passenger side rear 6" or so has been "repaired". The driver's side could have used the same repair in my opinion.
Engine:
2F w/ stock carb/dizzy/etc. Just got it fired up tonight with a little gas in the carb, no fuel tank connected. Here's a real short video I took w/ my phone to show it fired right up after sitting a couple of years.
http://www.youtube.com/watch?v=EPNOExUuOFg
I'll have cold compression numbers in a couple of days. The cluster had 44,377 on the clicker, but I have absolutely no idea if that is 144, 244, or even original to this cruiser.
Transmission:
Stock 4-spd. Probably need synchros, like every other tranny of this vintage. I have never driven this beast, but PO says it shifted fine.
TC:
Stock 4-spd case. Shifts easily 2/4 and hi/lo.
Axles:
Stock. Disc front, drum rear. Knuckles are clean. Warn hubs.
Stock wheels & $hitty roller tires.
$1,200 w/ VIN tag (matches frame)
$1,100 w/o VIN
REAR SILL ASSEMBLY SEEN IN PHOTOS NOT INCLUDED
Pictures in main "ForSale" forum:
https://forum.ih8mud.com/showthread.php?t=165984
Engine:
2F w/ stock carb/dizzy/etc. Just got it fired up tonight with a little gas in the carb, no fuel tank connected. Here's a real short video I took w/ my phone to show it fired right up after sitting a couple of years.
http://www.youtube.com/watch?v=EPNOExUuOFg
I'll have cold compression numbers in a couple of days. The cluster had 44,377 on the clicker, but I have absolutely no idea if that is 144, 244, or even original to this cruiser.
Transmission:
Stock 4-spd. Probably need synchros, like every other tranny of this vintage. I have never driven this beast, but PO says it shifted fine.
TC:
Stock 4-spd case. Shifts easily 2/4 and hi/lo.
Axles:
Stock. Disc front, drum rear. Knuckles are clean. Warn hubs.
Stock wheels & $hitty roller tires.
$1,200 w/ VIN tag (matches frame)
$1,100 w/o VIN
REAR SILL ASSEMBLY SEEN IN PHOTOS NOT INCLUDED
Pictures in main "ForSale" forum:
https://forum.ih8mud.com/showthread.php?t=165984
85roktoy
SILVER Star
I need the factory Roll bar main hoop for my 78 FJ40. PM me if you got anything! Thanks, Wes
Last edited:
265/70/17 Goodyear's FJ/Tacoma
I have two Goodyear Wrangler AT/D2's for sale. They are 265/70/17 size tires. They are 50,000 mile tires. These have less than 500 miles on them.
Looking to get $175 for local pick up and $200 shipped.
Pics here -------> http://www.pbase.com/kncrsr5r/for_sale
I have two Goodyear Wrangler AT/D2's for sale. They are 265/70/17 size tires. They are 50,000 mile tires. These have less than 500 miles on them.
Looking to get $175 for local pick up and $200 shipped.
Pics here -------> http://www.pbase.com/kncrsr5r/for_sale
jfz80
Cruisin’
tires tires tires and more tires......
things have gotten sanford and son here and time to get it back down to the basics b4 the citystarts fining me to store all this junk
4--- 285/75/16 goodyear MTR's (mentioned on page 9, now reduced)
8/16ths tread depth, 6 wheelin trips, they do have cuts but balance well
$350
4--- 36'' 12.5 r 15 swamper TSL's --- old tires probably best as a spare
lots of tread left but rough sidewalls, do hold air though
$25 tire only / $35 tire w/ black steel wheel(rough)
4--- 35 12.5 r 15 only 3/16" tread left but enough to have fun w/ and replace
your tiny 33's, (one has pinhole in shoulder of tread needs patch=free)
$25 each w/ steel wheel SOLD!!!!
4--- 31 10.5 R 15 Yokohama geolanders AT-II on stock tacoma alloy wheels
very nice tires, quiet, less than 10k miles, tread measures 1/2 inch
$300 tires $150 wheels $400 combo
4--- 33 12.5 r15 Winston Winners A/T
on 15x12'' aluminum wheels
(rattlecanned black) 2 @ 30% 2 @ 50% but there bigger than your 31's
$100 tires $200 combo
pics by request if i dont get em posted here, please respond by PM , thanks
things have gotten sanford and son here and time to get it back down to the basics b4 the citystarts fining me to store all this junk
4--- 285/75/16 goodyear MTR's (mentioned on page 9, now reduced)
8/16ths tread depth, 6 wheelin trips, they do have cuts but balance well
$350
4--- 36'' 12.5 r 15 swamper TSL's --- old tires probably best as a spare
lots of tread left but rough sidewalls, do hold air though
$25 tire only / $35 tire w/ black steel wheel(rough)
4--- 35 12.5 r 15 only 3/16" tread left but enough to have fun w/ and replace
your tiny 33's, (one has pinhole in shoulder of tread needs patch=free)
$25 each w/ steel wheel SOLD!!!!
4--- 31 10.5 R 15 Yokohama geolanders AT-II on stock tacoma alloy wheels
very nice tires, quiet, less than 10k miles, tread measures 1/2 inch
$300 tires $150 wheels $400 combo
4--- 33 12.5 r15 Winston Winners A/T
on 15x12'' aluminum wheels (rattlecanned black) 2 @ 30% 2 @ 50% but there bigger than your 31's
$100 tires $200 combo
pics by request if i dont get em posted here, please respond by PM , thanks
Last edited:
Have any pics of the 35's? I need a set b/c my 33's are too small with my 4.88's.
I would love to get the TSL's, but I need them to be able to drive on are they that rough, or just not pretty? Let me know as I will prob get at least a set of 35's from ya.
I PM'd ya.
I would love to get the TSL's, but I need them to be able to drive on are they that rough, or just not pretty? Let me know as I will prob get at least a set of 35's from ya.
I PM'd ya.
jfz80
Cruisin’
"I would love to get the TSL's, but I need them to be able to drive on are they that rough, or just not pretty? Let me know as I will prob get at least a set of 35's from ya."
yes they are that rough, and they are ugly
emailed you some pics
yes they are that rough, and they are ugly
emailed you some pics
Hey jfz80.....I've got a set of 33's with no rims....if you can't find a buyer who wants the rims I'll buy a set from ya....let me know....located in clemson.
Thanks, Chuck
Thanks, Chuck
I didnt get an email can you try again. deanmatt at hotmail dot com
I am def interested int he 35's and 36's.
(What brand are the 35's?)
Thanks.
I am def interested int he 35's and 36's.
(What brand are the 35's?)
Thanks.
FJ40 Fenders, Turn Signals, and Running Boards
OEM pair of FJ40 fenders bought new around 1999. Mustard yellow. Left is near perfect except for my having bent the inner lip up to ensure it wouldn't chunk tires, and the support is pulled off - other than that perfect. Right suffered from a roll - the out top edge is bent down a little - but could be fixed easy with some patience, the inner has a small dent I made to clear my battery tray. Solid, newer and no rust to deal with. $175 - could deliver to Tellico in August.
FJ40 front turn signals. One original 76, good shape a little loose at the pivot and the other bought new in 1999, with just a few blemishes from when it fell off on trail one with the wiring still intact and bounced off the tire a few times. Looks as new. $90 obo for both.
76 FJ40 running boards. Dings and scratches - sand blasted, marine epoxy primered and painted PPG mustard yellow in 99 - has holes drilled in left side for my highlift base. Decent solid shape. $40 for both.
Everything sold in pairs - can deliver to Tellico in August. Bill.
OEM pair of FJ40 fenders bought new around 1999. Mustard yellow. Left is near perfect except for my having bent the inner lip up to ensure it wouldn't chunk tires, and the support is pulled off - other than that perfect. Right suffered from a roll - the out top edge is bent down a little - but could be fixed easy with some patience, the inner has a small dent I made to clear my battery tray. Solid, newer and no rust to deal with. $175 - could deliver to Tellico in August.
FJ40 front turn signals. One original 76, good shape a little loose at the pivot and the other bought new in 1999, with just a few blemishes from when it fell off on trail one with the wiring still intact and bounced off the tire a few times. Looks as new. $90 obo for both.
76 FJ40 running boards. Dings and scratches - sand blasted, marine epoxy primered and painted PPG mustard yellow in 99 - has holes drilled in left side for my highlift base. Decent solid shape. $40 for both.
Everything sold in pairs - can deliver to Tellico in August. Bill.
