Fj40 3f or 1fz

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 13, 2019
Threads
1
Messages
4
Location
Ecuador
Hi there, i own a 1973 fj40 and i like to change the engine, don't know if 3f or 1fz, does the last one worth all the modifications? Or the 3f is enough? By the way my car has all ready a 5 gear h55f transmition.

FYI: i live in Quito Ecuador at 2800m or 9200ft

Waiting for your answers. 🤔🤔🤔
 
Like this? From an FJ40 down in Miami. This was in the showroom at the FJCo. Usually they tend to modernize the cars, which I’m not crazy about. But this one i snapped a photo of was, outside of some comfort stuff and this engine, was pretty stock.

8BD5C671-D934-409B-A5EA-82E86379D387.webp


19260DA2-26C1-4A0A-A5EE-BD119B97F1B5.webp


F1A7EAB1-3F78-4003-89E7-58F3A370C652.webp


3ED934BE-4E50-420B-AAD4-0EC46D8D909D.webp


5311FA81-D12F-40B9-AF6D-3E385142A205.webp
 
Hi there, i own a 1973 fj40 and i like to change the engine, don't know if 3f or 1fz, does the last one worth all the modifications? Or the 3f is enough? By the way my car has all ready a 5 gear h55f transmition.

FYI: i live in Quito Ecuador at 2800m or 9200ft

Waiting for your answers. 🤔🤔🤔

A 3F is just a de-stroked 2F. It will rev a little higher, at the loss of some of the low-end torque of the F/2F. If you drive your 40 mostly on the highway, it might be better than an F/2F but there is not a huge difference. But if you use your 40 mostly off-road or at less than highway speeds, then I would rather have the F or 2F.

The 1FZ would be a definite improvement in terms of power and speed, but a lot more work to install in a 40 than the 3F which would be close to a bolt-in.
 
A 3F is just a de-stroked 2F. It will rev a little higher, at the loss of some of the low-end torque of the F/2F. If you drive your 40 mostly on the highway, it might be better than an F/2F but there is not a huge difference. But if you use your 40 mostly off-road or at less than highway speeds, then I would rather have the F or 2F.

The 1FZ would be a definite improvement in terms of power and speed, but a lot more work to install in a 40 than the 3F which would be close to a bolt-in.
A 3F is just a de-stroked 2F. It will rev a little higher, at the loss of some of the low-end torque of the F/2F. If you drive your 40 mostly on the highway, it might be better than an F/2F but there is not a huge difference. But if you use your 40 mostly off-road or at less than highway speeds, then I would rather have the F or 2F.

The 1FZ would be a definite improvement in terms of power and speed, but a lot more work to install in a 40 than the 3F which would be close to a bolt-in.

Hi, thanks for your answer, my 40 is my every day car, and my offroad car, for that reason i dont know if i should change the engine, but you said that the 3f does not make a big difference, should i buy a 1fz?
 
a 3fe is a major improvement over an F or 2F engine. Run-ability is way better and I didn't notice any less low end power than a 2f. The only thing I don't like about the 3fe is the rev-limiter and the limp mode caused by WOT for too long. I think a 3fe and an H55 would be a sweet setup in a 40 series. A 1fz would be even better but a bit more complicated and hard to get the h55 behind it.
 
a 3fe is a major improvement over an F or 2F engine. Run-ability is way better and I didn't notice any less low end power than a 2f. The only thing I don't like about the 3fe is the rev-limiter and the limp mode caused by WOT for too long. I think a 3fe and an H55 would be a sweet setup in a 40 series. A 1fz would be even better but a bit more complicated and hard to get the h55 behind it.

He's in Ecuador; he's talking about a carb'ed 3F, not the U.S. market 3FE.
 
Hi, thanks for your answer, my 40 is my every day car, and my offroad car, for that reason i dont know if i should change the engine, but you said that the 3f does not make a big difference, should i buy a 1fz?

If you've got the skills to fabricate motor mounts, install a different radiator, and make a wiring harness to fit the ECM in your 40, sure - but it's going to be a lot more work than dropping in an F-series engine.
 
Back
Top Bottom