Exhaust Valve Seats

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Mr. Toad

20 Year 15 Year 10 Year
Joined
Feb 7, 2005
Threads
63
Messages
1,643
Anyone have any BTDT pros and cons of installing new exhaust valve seats when rebuilding the head? As opposed to re-grind, I guess? The seats are pricey.
 
If they are servicable, I'd just have a valvejob done on it. If you have a '75 motor(from sig line), they should be hardened valve seats for unleaded.
JMO

Ed
 
Thanks. And yes, it's a '75 engine. Can the hardened seats be reground during a valve job?
 
FYI...

I have a '72 "F" engine, when we rebuilt it the machinist recommended putting in hardened exhaust seats and I did. I'm sure it was a good decision.

I'm pretty sure in '72 the PO was NOT running unleaded gas :rolleyes: :D

Jody.
 
I have been getting heads rebuilt for 15 years now [for the shop] and am still on the fence about this. The first machine shop to pitch these to me did a good sales job and I went for it. About a year later, we were servicing the head again because the seats had 'moved' [don't remember the technical term for this] and the valves were no longer closing. :mad:

I have a very hard time recommending something to a customer that may only cause them more greif later on.

That said, I think the issue could be avoided if you had a permanently mounted vacuum guage so that you could watch for the signs of moving valve seats [flickering reading on the guage] and stay up on your valve adjustments.

Bottom line: Ask your man point blank if yours can be re-cut. If he says yes, but hems and haws about the unleaded gas thing, just tell him to leave well enough alone and re-cut the ones that are in there. They are more likely to be stable and stay stable. :)
 
Thanks all. Plan -- pull head, get valve job done with seats re-cut. Only replace what needs replacing. I'll update after the work.
 
Degnol wrote: . . . If you have a '75 motor(from sig line), they should be hardened valve seats for unleaded.

Anyone know when Toyota started putting hardened seats in the F/2F heads?
 
Mr. Toad said:
Anyone know when Toyota started putting hardened seats in the F/2F heads?

That would be the year where the little tag says "unleaded gas only".
 
FWIW...I ran into the machinist last weekend that I've used on a variety of different engine builds...one of these being the head on my 73 TVR. While it was needing other work...we opted to install the hardened exhaust seats. I had my 73 40 in the parking lot and we were chatting it up about another SBF that was recently freshened up and had the heads machined for O-ring style HG's at his machine shop and how nice it runs...bla bla bla....then I asked him if I should consider pulling the head off the 40 and having him put in hardened seats. He looked at me as if I was speaking from the orifice at the other end. In a nutshell, he said if and when you ever need to pull down the F motor/head...we would look at it...but his experience is that it probably wouldn't be necessary. He said he's seen quite a few F motors and the seats have never been an issue with them. I am not as concerned about running unleaded after this discussion. If and when the time comes...we'll look at it then.
 
toddslater said:
FWIW...I ran into the machinist last weekend that I've used on a variety of different engine builds...one of these being the head on my 73 TVR. While it was needing other work...we opted to install the hardened exhaust seats. I had my 73 40 in the parking lot and we were chatting it up about another SBF that was recently freshened up and had the heads machined for O-ring style HG's at his machine shop and how nice it runs...bla bla bla....then I asked him if I should consider pulling the head off the 40 and having him put in hardened seats. He looked at me as if I was speaking from the orifice at the other end. In a nutshell, he said if and when you ever need to pull down the F motor/head...we would look at it...but his experience is that it probably wouldn't be necessary. He said he's seen quite a few F motors and the seats have never been an issue with them. I am not as concerned about running unleaded after this discussion. If and when the time comes...we'll look at it then.

Good story. Thanks. :)
 
Back
Top Bottom