Engine rebuilt

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 20, 2006
Threads
139
Messages
4,041
Location
Pequot Lakes MN
I just bought a 2f engine for my 74 and I want to get it all rebuilt before I put it in... Guess my question is I dont really know where to start? I dont know what I need to ask the machine shop and dont know about what somthing like this cost.. can anyone give me a list of what should be done, since I got the engine out, and dont want to do it right...

Thanks!
 
I just bought a 2f engine for my 74 and I want to get it all rebuilt before I put it in... Guess my question is I dont really know where to start? I dont know what I need to ask the machine shop and dont know about what somthing like this cost.. can anyone give me a list of what should be done, since I got the engine out, and dont want to do it right...

Thanks!


Hope that's a typo!

Do you know it needs to be rebuilt? Many times re-ringing and new bearings will be all you need. Plasigauge is a great tool for determining clearances on bearings.

I tore down my 2F and had it bored and new cam bearings installed($150), new pistons($300) rods checked ($48) head checked for true, valve guides checked for wear and valve seats re-cut($105) new cam ($200) and lifters($100) used a Toyota engine rebuild gasket set($250?) and a friend ground the valves and helped me reassemble the whole thing. The crank was in spec so it got crocus cloth dressed. New main and rod bearings(about $100 total, IIRC) and the flywheel surfaced. I think I had a total of about $1300 in everything by the time I was done.
The machine shop also cleaned and peened the head and the block. They baked it a 600* then blasted steel shot through the whole thing. The heat is supposed to strain-relieve the metal, dunno.
The only reason I had it bored was that the wrist pins were loose so I needed new pistons.
The motor had 89K on it and I probably could have put seals in it and run it.

GL

Ed
 
yes... that is a typo... hahha!! thanks... yes this motor has 83K on it... well that is what the speedo said... I have no idea if that was correct... the guy I bought it from said it ran... never heard it run (guess that is where I am worried) he pulled it right away and put in a 350... By the looks of the carb I dont know how it could have ran, but who knows... I just dont want to not do something now and wish I would have done it when I had the engine out you know...

Thanks again
 
Well, I would put it on an engine stand and start checking clearances before diving in. You can probably rent a bore gauge, micrometer and buy some Plasigauge. I was very fortunate to have a semi-retired mechanic friend help and guide me through the whole process. He would have put rings and bearings in it and run it.......but I wanted it as perfect as I could make it. With a little maintainence an F or 2F is a very sturdy motor and many have well over 200K on them and are running strong. Kinda depends on where it is wear-wise.

GL

Ed
 
Paying someone to rebuild a 2F can be fairly expensive, I have a friend here that had his done it was 2700 bucks before it was done. Larry
 
And on selecting a machine shop......I would try very hard to find someone local with a good reputation. I heard it rumored that a lot of the chain parts stores actually ship stuff to Mexico to have machine work done. That may or may not be a good thing, but I sure like having someone close to answer questions and be accountable for their work.

GL:beer:

Ed
 
well I am definatly going to have to pay some one to do it.... so guess I will start calling around and getting prices
 
well I am definatly going to have to pay some one to do it.... so guess I will start calling around and getting prices

Let us know what you find out if you don't mind.

good luck

Scott
 
Back
Top Bottom