Electric Locker Malfunction

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 15, 2006
Threads
5
Messages
12
Location
Elizabeth City, NC
My rear locker stopped working a few months back. The toyota dealer replaced the computer that controls both front and rear locker motors. A new motor for the rear locker is $850.00 approx., so I bought a used one from Cruiserparts.net. It didn't work so the menchanic took working parts from both motors and got it to work. A few weeks later (today) both lockers will not engage. I have used quick locks in a 5 speed pick up with great sucess. Should I replace both lockers with quick locks or powertrax lockers? Can this even be accomplished on axles equiped with electronic lockers? I am supposed to go to Telico 7 June and need to act quick. The mech that did the repairs is going to look at it Thursday is there something he should be looking for? Help!

JD
 
Is the center differential lock (CDL) engaging? It must be locked before the front and rear lockers are allowed engage. The CDL only engages in low range unless you have added a CDL switch to the dash.

There are quite a few threads on this topic of how to get the lockers working. If you haven't already done so, the search engine may help you answer your questions.
 
If you get different lockers, ARB lockers are the best choice overall for a vehicle like your Cruiser. They are even stronger also.
 
When I first got my 80 I took it in because the lockers wouldn't work.

They told me the ECU was bad. They also told me it wasn't covered under teh warrenty.

I got on 'Mud and read about the cleaning procedure and fixed it myself.

I went back and got my diagnostic money back.

Most ECUs work by sending power to the device and you can feel the relays click. The locker ECU requires a signal from the locker to confirm its in the correct position so it doesn't click. It's an easy missed diagnoses when done by someone who doesn't know cruisers.
 
I am still troubleshooting my rear locker dilema. I don't think the actuator is getting any power. This is what I did.

Put the truck in 4x4 low range and turned it off.

Turned the ignition back on with out turning on the truck.

Partner actuated both lockers, I could here the front engage but not the rear.

I put a volt meter on the plug and had partner engage the locker and got no indication of power going to the actuator.

This is how I checked for power, I placed the ground on the black and white wire and checked the others (blue, green)with the positive lead and did not get any indication of power.

Did I miss something or check for power incorectly?
 
Does the shaft that holds the final gear, and drive gear rotate when the motor turns?




No it does not rotate the shaft, it acts as a piston hence the need to be moving in an arch to create a differential in RPM between the dog collar and the differential. This allows the respective teeth to mesh.
 
Last edited:
Well CG; let me see what my foggy brain can come up with. First read every thing u can find on the lockers. If u don't have the EWD (Electrical Wiring Diagram) manual [No. EWD189U], u can download the PC ZIP file from here:

FZJ80 LOCKER WIRING DIAGRAM from Yankeetoys web site PC ZIP file
http://www.yankeetoys.org/Docs.htm

The DIFF LOCK ECU (D5) is located somewhere behind the right hand kick panel. The connector output is called ID1 and located behind / near / above the left kick panel. There are three connectors; ID1, BQ1 & Bh2 before D5 connects to the rear diff lock control motor.

I would suggest getting the EWD manual for trouble shooting this; there is a lot going on with the wiring and relay control circuits. I don't have an actual schematic for D5.

Does anyone have a schematic for D5, "DIFF LOCK ECU"?

...
 
Back
Top Bottom