Ebay HID Projector Wiring Tutorial

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2004
Threads
178
Messages
1,417
Location
Athol, MA
After much searching and frustration I was informed that some, if not most, of the HID Projector headlights sold on Ebay are for the Non North American version of the 80 series. With that being said, these need to be modified to work in our North American 80 series.

These are HID headlights I purchased off Ebay.
LP-TLC91-YD_HID.webp
KAZE_DIGITAL-HID.webp
sonar_91-97_landcruiser_black_pro_hl.webp
 
The first mod is to eliminate the three prong connector. Cut it out... This is only needed on the Non North American 80 series.
You will remove the rubber cover on the low beam side covering the HID lamp.
Cut and remove the three prong connector as well as the connector on the other end.
IMG_1055.webp
IMG_1053.webp
IMG_1044.webp
 
You will end up with a black and red wire leading out from the high beam light.
IMG_1063.webp
 
Remove the side marker socket that came with the houseing and replace it with the one from the factory. This is a direct fit. This will allow a factory connection for the side markers.
IMG_1056.webp
IMG_1059.webp
 
The red connector coming from the ballast plugs into the factory Low beam connector.
IMG_1066.webp
 
The small black and red wires power the halos around each light. I suggest wiring these into the same circuit as the side marker lights.
IMG_1068.webp
 
The black and white wires at the bottom of the lights power the three "Cat Eye" lights. I am not wiring these as I don't care for the look. If I did I'd wire them with the halo lights and the side marker lights.
IMG_1067.webp
 
Now all that is left to do is remove the old lights and replace them with the HID lights. You can even upgrade the 55w high beam that comes with the housing with a 100w Hella bulb. I'd also seriously consider Slee's upgraded harness.
 
H1 55w that came with the housings.

The H1 bulb comes in 55W, 70W, 100W, and 130W

Hella Bulbs
IMG_1071.webp
IMG_1072.webp
 
The red plug as designed has a raised portion that is designed to lock into the factory connector. If plugged in this way the lights will not work. The polarity is wrong. Solution, file down the raised portion and this will allow you to plug it into the harness rotated 180 degree. Correct polarity, lights now work.
 
Well, I like the looks of the black lights against my black truck, but I don't think the light output on the HID low beams is anywhere near the light output of my John Deer HIR bulbs that I had in the stock lights.
IMG_1116.webp
 
How do they fit? Decent quality moldings and seem like they will hold up for many years? Thick front plastic lense?

I am looking for some quality housings with a clear lenses so I can chop them for HID retrofits, (prefer glass but to my knowledge nobody has them.)
 
I don't think the light output on the HID low beams is anywhere near the light output of my John Deer HIR bulbs that I had in the stock lights.

Good to know. I'll keep my HIR's then.
 
How do they fit? Decent quality moldings and seem like they will hold up for many years? Thick front plastic lense?

I am looking for some quality housings with a clear lenses so I can chop them for HID retrofits, (prefer glass but to my knowledge nobody has them.)

depo headlamps are ideal, but very hard to find now.
 
depo headlamps are ideal, but very hard to find now.

If you are (Not "you", necessarily, but anyone) is interested in getting a pair and are willing to pay an arm and a leg I can still get them, but you better be wanting to get them pretty bad(ly)!

I don't want to pollute MSG's thread, so please PM me if you gotta have it.

ANYWAY, I know that these headlights were designed to be used with halogens, but I'm surprised that the light output is less than that of HIR's.

How's the light pattern?
Sharp and even or not so good???
 
last ot post, but I already got a set. Maybe the last cheap set.
 
Back
Top Bottom