Early Splines/Third Member Interchangeability

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 25, 2011
Threads
89
Messages
3,680
Location
Harbour City, the New Southern Wales
Website
www.freewayoneentertainment.com
1970 FJ45 w/3.70's. The rear third in my truck is making metal and a friend has a good front centre going to waste. Spline count aside, is a front centre a direct swap for the rear? Front is FF, rear is SF.

:cool::cool::cool:
 
WAiT just a minute, non rear ff? Can’t be too hard to source a ff in oz? Reckon the old girl deserves a REAL rear end!!

This fella’s got a movie to finish! Filmmaking’s a more expensive hobby than blow!!
 
I think coarse spline ones will interchange with fine spline ones, but from memory the crownwheel and pinion are different. Not sure if you can swap the spider gears or not. Is your mates one a coarse spline too?
 
Only differences front to back is the back has a block on the spider gear pinion to hold the inner axle out so C clips don't fall out. Will need to pull the pinion shaft out to remove the C clips out. Would pull it out just enough to remove the block then slide the pinion back in. Slide the inner axles out and pull the diff. Only thing I would do different when switching out pull the bolt holding the pinion shaft while diff is out since it's easier to get to.
 
I think coarse spline ones will interchange with fine spline ones, but from memory the crownwheel and pinion are different. Not sure if you can swap the spider gears or not. Is your mates one a coarse spline too?

Both are fine. Coarse spline stopped at the end of 1967 or thereabouts.

@Living in the Past - thanks John, have the removal sorted! Just wondering if the front centre has provisions for c-clips!

06C90567-14E6-440F-8169-9EEB3CA80876.webp
 
Both are fine. Coarse spline stopped at the end of 1967 or thereabouts.

@Living in the Past - thanks John, have the removal sorted! Just wondering if the front centre has provisions for c-clips!

View attachment 2045449

I switched them in my early 68 back in the mid nineties. Never heard of the side gears not having cut out to retain C cilps. Just need to reuse the C clips and pinion shaft block.

The date for the switch from coarse to fine inner axles was not clear. May have happened when the bolts for driveshafts went from 8MM to 10MM. My early 68 model has both coarse inner axles and 8MM bolts on the driveshafts.
 
I switched them in my early 68 back in the mid nineties. Never heard of the side gears not having cut out to retain C cilps. Just need to reuse the C clips and pinion shaft block.

The date for the switch from coarse to fine inner axles was not clear. May have happened when the bolts for driveshafts went from 8MM to 10MM. My early 68 model has both coarse inner axles and 8MM bolts on the driveshafts.

Thanks John! Any idea if you can install fine spline spider gears on a coarse spline third?

@whitey45 maybe you know?

Also maybe @65swb45 Mark?
 
If you use a front 3rd member on the rear you will need the spacer and shims from Toyota. The front third member does not have them, well at least on a 40. I think this is what @Living in the Past , John was also referring to.
 
Thanks everyone for your replies. Turns out after all these years these were 4.11’s! I’m off to find me a SF 4.11 centre.
 
1ACDD620-EFCA-4DCC-BEFD-79DCB41E18BE.webp
 
Okay, last Q. Can you run a SF centre in a FF housing? Say an FJ40 SF 4.11/.370 in a HJ75 housing? I know FF centres from both models are the same, just unsure about SF vs. FF.
 
Personally would look for a front 4.11:1 and use the block and C clips front you semi floater. I do see front and rear side gears are the same from 3/69-7/80. The block is call a spacer and available in different thicknesses.

Okay, last Q. Can you run a SF centre in a FF housing? Say an FJ40 SF 4.11/.370 in a HJ75 housing? I know FF centres from both models are the same, just unsure about SF vs. FF.


Yes just leave out the block and C clips.

PS: on your axle hunt if you come across any OEM limited slip diffs I'm interested. While not here these we're a option on the 40 series from 1/79 on.
 
Personally would look for a front 4.11:1 and use the block and C clips front you semi floater. I do see front and rear side gears are the same from 3/69-7/80. The block is call a spacer and available in different thicknesses.




Yes just leave out the block and C clips.

PS: on your axle hunt if you come across any OEM limited slip diffs I'm interested. While not here these we're a option on the 40 series from 1/79 on.
G’day John,

Will keep an eye out for an OE LSD.

Any idea if you can run a FF centre in a SF housing? Just change spider gears?
 
G’day John,

Will keep an eye out for an OE LSD.

Any idea if you can run a FF centre in a SF housing? Just change spider gears?



G'day Dan,

It all with interchange as long as you match the spline count on the side gears. Being 4.11:1 ring and pinion should be a lot easier than 3.70:1 to find. The pattern on the driveshaft is going to be harder since it changed for the four speed.
 
G'day Dan,

It all with interchange as long as you match the spline count on the side gears. Being 4.11:1 ring and pinion should be a lot easier than 3.70:1 to find. The pattern on the driveshaft is going to be harder since it changed for the four speed.
Semi float side gears (spider gears I think we call them) can be installed into a fully float centre? What about the provision for the spacer block and bolt?

I have a terrain taker multi fit flange.
 
Back
Top Bottom