driving in circles

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 12, 2007
Threads
69
Messages
329
Location
Tucson, AZ
so I have been driving in circles very slowly on gravel in both direction trying to get my lockers engaged..no luck. just flashing. I try the rear first and cant get that to engage by itself then both and still just both lights flash. I don't know when the last time they were used . I have owned the truck for about 8 month and the PO had no idea what they did. he owned it for 4 years. CDL is working fine. one thing I noticed is that there is movment in the 4wd shifter (about a 1/4 of an inch) when I put it in low. stick just kind of moves forward and back a tiny bit by it self while driveing forward.

Is there anything else I can do or do I need to take it to a shop.

Thanks all.
 
To expand on what Tools R Us said; try parking in a quiet area and flip the rear differential lock switch. Listen closely for the sound of an electric motor under the vehicle (from the differential actuator). It might help to have somebody else sit in the driver's seat and flip the switch so you can place yourself near the differential and get a better vantage point.
 
dose the engine need to be running to do this or can I just have accessories on?
 
dose the engine need to be running to do this or can I just have accessories on?

CDL locked, ignition on, engine off.
 
Baran,

Sounds like classic case of the lockers needing simple exercise. Make a point of messing around with them on gravel a couple times a week or whenever you feel like it. Before long they'll start working. If using a tight circle, move SLOWLY to give them a chance to slip into engagement. After you get them free of the crud that's hindering their movement, do this monthly or so if you don't wheel. If you have not already done it, now is the time to drain and refill the differentials with some fresh oil that will help dissolve crud with its fresh additives. The gear oil might be 13 years old....

Or you could go to a dealership and pay $500 to have them opened and cleaned by hand.
 
No sound

So what is the issue if you don't hear the motor cycle? I'm having a problem with the front on mine. I can hear the rear one cycle (and it locks fine) but nothing with the front. I can hear a little click in the cabin for both of them (a relay or something). Where do I go from here. I can't seem to find any posts on removing/cleaning them.

Thanks in advance,
Kyon
 
So what is the issue if you don't hear the motor cycle? I'm having a problem with the front on mine. I can hear the rear one cycle (and it locks fine) but nothing with the front. I can hear a little click in the cabin for both of them (a relay or something). Where do I go from here. I can't seem to find any posts on removing/cleaning them.

Thanks in advance,
Kyon

Did you check the fuses for the fronts? If you just get a clicking then its most probably ur motor, if you head nothing then you might have a lose connection.
 
So what is the issue if you don't hear the motor cycle? I'm having a problem with the front on mine. I can hear the rear one cycle (and it locks fine) but nothing with the front. I can hear a little click in the cabin for both of them (a relay or something). Where do I go from here. I can't seem to find any posts on removing/cleaning them.

Thanks in advance,
Kyon

If the relay is clicking it's probably sending power to the motor. If the motor isn't turning, it and/or the first actuator gear is probably bound up, rusted, old grease, magnets fell off, etc. If you continue to put power to it chances are that the smoke will come out of the motor, requiring a new $$$ actuator, been there, done that.:o

That's why my first check is, see if the motor is running, if so then isn't going to damage anything to play with it. If it's not running then you need to determine if it has power to it, if there is no power then it's a wiring, control box, etc issue. If there is power going to it, then the motor is burned and/or bound up and putting power to it will not do any good and could destroy it. If it's bound up it need to come apart, get cleaned, freed up and greased or replaced.

There are several good threads, search for actuator repair, rebuild, etc. The front, center and rear are very similar in construction and operation, with the main differences in timing and mounting, so good info can be found from the post on any of them. Also an FSM is highly recommended for troubleshooting them.
 
cool, as usual you guys all rock!

still have not figured it out but now I have a better understanding of what I'm doing.
 
If the motor isn't turning, it and/or the first actuator gear is probably bound up, rusted, old grease, magnets fell off, etc.

There are several good threads, search for actuator repair, rebuild, etc. The front, center and rear are very similar in construction and operation, with the main differences in timing and mounting, so good info can be found from the post on any of them. Also an FSM is highly recommended for troubleshooting them.

What is the "first actuator"?

The threads are okay but none are start to finish that I could find. I just got the 80 today so I don't have the FSM as of yet. It's on the list...

Thanks
 
What is the "first actuator"?

The threads are okay but none are start to finish that I could find. I just got the 80 today so I don't have the FSM as of yet. It's on the list...

Thanks

"First actuator gear" or the first gear that the motor turns. If this gear or the motor bushings are bound the motor wont turn. If power is applied the motor windings overheat, apply power for too long and the $$$ smoke will escape from the motor windings.

The first, input, top or whatever you want to call it gear has wiper switches on it that control how long the motor runs, how far the gear turns. If that gear doesn't turn the circuit continues to apply power to the motor.

If the motor runs for a second and stops when the switch is turned, the bind is in the output part of the actuator and you probably wont damage it by "exercising" it. IMHO if the actuator is bound, slow, etc the best plan is to take it apart, clean and grease, a freshly greased one will always be quicker and more reliable.
 
Back
Top Bottom