Doors unlock when cornering?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I went the reallllly cheap route, I put a couple of 1" X 1" squares of duct tape right where the door sensor/plunger mechanism hits the door frame and the problem completely disappeared, the contact point must have been just that millimeter or so from completely making positive contact. For now its easier than disassembling the sensors and shimming them somehow.
 
The FSM, EWD, and Transmission Manual are three separate manuals. The FSM is the most commonly used and it covers everything except electrical schematics and transmission rebuild, you would need the EWD and Transmissions Manual for that. The FSM is readily available, but the EWD and Tranny manual are harder to find.
 
You don't have to shim the door jamb sensor really. You can glue something to the end if the plunger like gasket, plastic or whatever. The door jamb switch new is around 15 bucks I think. Also the same switches are on lots of similar year toyota vehicles in bone yards.
 
No other inputs, yet ;) Thank you for your reply though! When I can, I'll keep digging here.

What a EWD? I have a Nissan Z car and have its tech manual with everything down to its gnat's booty. Having the Nissan tech manual has been so helpful! I can't seem to find one for this 1995 LC though. Is there one? If so, where can I get one - do you know?


Update: My brother and his guys found the schematics for my LC. If anyone can figure out these electrical issues in my TLC, it would be him :) BUT if you all have any recommendations, let me know! Thanks again!
 
Doors unlock when cornering?

Let us know when they start opening. :)



But seriously, lately my doors have been locking/unlocking on their own. I recently tried disconnecting a non-fuctional aftermarket alarm and crazy s*** started happening, so I just put things back the way they were. But now I notice that they unlock while driving when I lightly kick the DS kick panel. Which is where most of the wiring runs. Maybe you have one too and are hitting it with your foot on turns.
 
Last edited:
Wayne, How would I check "master door lock switch, on the master switch panel, on the driver's door"? Recently my power door locks and windows "went out" along with my 1st row chairs. Today, when I replace the fuse the doors and windows and it immediately shorted. The security system still seems to work though.

Do you (or anyone on this forum) have the any information (wiring diagrams, how to open and check) the entire door panel that controls the windows and door locks?

Do you know if/how the 1st row chairs could be related to this fuse and/or the driver's door panel?
Wayne, How would I check "master door lock switch, on the master switch panel, on the driver's door"? Recently my power door locks and windows "went out" along with my 1st row chairs. Today, when I replace the fuse the doors and windows and it immediately shorted. The security system still seems to work though.

Do you (or anyone on this forum) have the any information (wiring diagrams, how to open and check) the entire door panel that controls the windows and door locks?

Do you know if/how the 1st row chairs could be related to this fuse and/or the driver's door panel?
 
Wayne, How would I check "master door lock switch, on the master switch panel, on the driver's door"? Recently my power door locks and windows "went out" along with my 1st row chairs. Today, when I replace the fuse the doors and windows and it immediately shorted. The security system still seems to work though.

Do you (or anyone on this forum) have the any information (wiring diagrams, how to open and check) the entire door panel that controls the windows and door locks?

Do you know if/how the 1st row chairs could be related to this fuse and/or the driver's door panel?
I have factory diagram and it shows how to test switch continuity and such on that master panel. If you will need it I can snap a photo and send to you. Copy the whole page is photos won't work. Let me know. DLPDLP
 
Update: after chasing things all over, it turned out that the catch on the passenger front door frame was loose :bang: so after tightening it up all is good. I was really so ready for it to be wiring or a switch that I didn't follow the rule of check the simplest thing first!!:doh:
 
Alex, I'm glad you found your problem and it had an easy fix.
 
Back
Top Bottom