Difficult to flush coolent?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Update:

I went back to the dealer today (they're actually open on Sundays) and had them do a 2nd flush. They did this at no charge.

However, I think I'm worse off for it. Whereas before I had what appeared to be bright green coolent with a hint of red, now looks like brown coolent. And whereas last time, they charged me for 2 gallons of red coolent, this time they used 1 gallon of red, according to the bill.

Again, it was free since they agreed they screwed up the 1st flush, but now I think I truly have mixed green/red, and it looks and smells funky.

I know I'm screwed. I plan to talk to the service manager, but I'm sure even if they agree to do it a third time, it won't be done right. The best I can do is give them a bad mark with Toyota Customer Service, which I'm sure I'll do in the end.

So, my questions are this. How bad is mixing the red/green and how long before this sludge I hear about will form.

Living in an apartment, flushing myself the conventional way is not possible. But I have some ideas about hiding in my garage and using a waterhose to flush and a bucket to catch and then toss when full and repeat multiple times until it's properly drained. I might be able to pull that off.
 
Do you know anyone with a wash bay, like a firefighter? After my HG job, I decided to go from red to green only because there's no Toyota dealers near me. Sides, if someone on the road ever needs some coolant, I'll have the green stuff!

I filled with water without the t-stat and ran if for a few days, then took it to the wash bay. Disconnected the upper and lower radiator hoses and ran it for about 30 minutes with both heaters on full, then flushed the radiator from top to bottom and from bottom to top, to get all the crud on the top of the tank out. Everything was crystal clear, until I decided to check the heater cores.

I disconnected the inlet hose off the valve and disconnected the upper and lower return hoses off the firewall, and flushed eash of them individually with water, then with an air hose.

The water would push out crud till it was clear, then I'd pump out the water with air. It would spit out rust, then I'd run water until clear, then air. I did this about 50 times until it was finally clear.

It took a lot of water and a good sump for it to drain into. Only then did I feel comfortable changing colors.

Find a good place to do it yourself.

-Eddie
 
I offered to help back when you first posted this up. The problem, I am in Bend, OR.

Are you sure you do not know anyone with a garage that lives near-by? Buy about 6 to 8 buckets (5 gallon) and promise a neighbor that you will not make a mess.

Whatever you do, do it as soon as possible.

Riley
 
Get a large tote that will fit under the truck to catch the old stuff. Get about 20 gallons of distilled water and 2 gallons of toyota red. Drain....fill radiator with water run engine with heater on for 10-20 minutes and repeat (until you get clear water). I did this about 5-6 times and eventually showed clear water. I put in 1 gallon of red and topped off the overfill. I had a hose at home and ended up not using it so I would not get any water deposits in the system. If they wont allow you to do at your complex - got to a DIY spray and wash and do it there.
 
Update:

However, I think I'm worse off for it. Whereas before I had what appeared to be bright green coolent with a hint of red, now looks like brown coolent. And whereas last time, they charged me for 2 gallons of red coolent, this time they used 1 gallon of red, according to the bill.

Again, it was free since they agreed they screwed up the 1st flush, but now I think I truly have mixed green/red, and it looks and smells funky.

I know I'm screwed. I plan to talk to the service manager, but I'm sure even if they agree to do it a third time, it won't be done right. The best I can do is give them a bad mark with Toyota Customer Service, which I'm sure I'll do in the end.

So, my questions are this. How bad is mixing the red/green and how long before this sludge I hear about will form.


Why are you worried about it now? It was already explained to you not to do this, not to let it happen etc., and you didn't listen. The same advice still stands. :rolleyes:
 
I wonder if you could send it off to Blackstone and have them analyze it. You could send them some virgin red and then some out of the radiator.

Personally, I would of asked to sit there and watch them do the flush, after they botched the first one.

If you're going to try and drain it yourself and catch all the fluid, you should use something about the size of a baby pool. Once the two plugs are pulled, after hitting cross bars and tie-rods etc... the stuff kind of ends up dripping everywhere.

:beer:
Rookie2
 
Why are you worried about it now? It was already explained to you not to do this, not to let it happen etc., and you didn't listen. The same advice still stands. :rolleyes:

I think you were dead right, when you suggested they didn't change it at all or used green coolent. But they constantly insisted that it was changed using red coolent. Even the original mechanic came forward and explained what he did.

Having never experienced what mixed coolent looks like, I just assumed I must have red and green mixed together. But now that I've seen mixed coolent, I know that you were right and it wouldn't have looked that green.

I clearly messed up and its entirely my fault. I'm kind of sorry I posted my foul up here. But maybe this will help someone else who might be as stupid enough as I was to take it to a dealer to have it flushed.
 
I think you were dead right, when you suggested they didn't change it at all or used green coolent. But they constantly insisted that it was changed using red coolent. Even the original mechanic came forward and explained what he did.

Having never experienced what mixed coolent looks like, I just assumed I must have red and green mixed together. But now that I've seen mixed coolent, I know that you were right and it wouldn't have looked that green.

I clearly messed up and its entirely my fault. I'm kind of sorry I posted my foul up here. But maybe this will help someone else who might be as stupid enough as I was to take it to a dealer to have it flushed.

It will be a good life lesson for you to trust your gut when it conflicts with what someone is telling you. The mechanics didn't want to admit they didn't do work they charge you for, it was fraud.

You are going to need to find a place that you can flush the fluid out, whether it be a friends, family, or small shop that will actually flush it. At this point you may want to go ahead and try doing a drain and refill of just the radiator with water to get some of the junk out. You should always run coolant but not having any for a week won't hurt (and there will still be some in there from the drain an fill).

To get the crud out of there, you are going to need to really flush the system, preferably both directions. It will take 50+ gallons of water.
 
Yep, I know it now. I have a plan. I do have a garage and I think I can probably get it done, but it will be a real pain.

Funny thing is, I looked at it again today and now it's green again! But here's the interesting part. My cap had red drops on it and as I removed the cap, the red drops fell into the green and then sunk down.

I'm guess, the red coolent is heavier than the green coolent and that's why I keep seeing green at the top and no red. I'll bet when I go to drain it, I'll have a bunch of red coolent come out, then green. That will be interesting to see.
 
Brian,
you can get it done w/ a big plastic catch container (like something from Target- like rubbermaid storage or something)

pull the plug on the engine... well, I guess you already searched and read all this stuff.

maybe they flushed but just didn't get every bit and the green is coming to the top- that's interesting the red falls to the bottom.
good luck, we all go thru ups n downs.
 
Funny thing is, I looked at it again today and now it's green again! But here's the interesting part. My cap had red drops on it and as I removed the cap, the red drops fell into the green and then sunk down.

I'm guess, the red coolent is heavier than the green coolent and that's why I keep seeing green at the top and no red. I'll bet when I go to drain it, I'll have a bunch of red coolent come out, then green. That will be interesting to see.

Odd...Question as I'm not sure how long it will be before you get to doing the flush properly but can you siphon off the green on top and refill with distilled water, run it and check the radiator again and repeat as necessary? If the green truly does come to the top that is.

Personally if it were me I would keep taking it back to the people that did this and get it in writing that if you develop a HG problem in the near future they will address it. It amazes me that they can look you straight in the face and state they did the job, or at least did a good job. Akin to a tire place rotating your tires and not torqueing down the lug nuts and telling you it isn't their fault the tires came off :frown:
 
Update:

I should point out that its the techs that claim they did the flush using the red coolent. The service advisers and now the service manager have been nothing but helpful, so I'm happy about that.

Today, the service manager called me and offered to come pick up my Land Cruiser and do again while I'm at work. This was after I wrote the manager an email detailing what happened.

I figure I got nothing to lose. If they don't do a proper job this time, I'm just back where I am now, but with all this hoopla, maybe they'll actually do it right this time.

To be fair to the techs, with two heater cores, it's very possible that the standard dealer flush, just doesn't cut it and if green truely does rise to the top in the radiator above red, then even a little amount might make it appear that no flush ever took place.

The manager said that they have two flush tanks, one with red and one with green and he thinks the green tank was used each time and there's actually no red coolent in there. That's possible. My overflow tank has red coolent in it, so any red that I'm seeing or mixture, could be coming from that overflow tank.

This is what the coolent looks like right now, before they pick up for the 3rd flush.
coolantpic.webp
 
Final update:

I got my rig back. And the coolent is blood red, just as it should be. The manager told me that when they drained it, a lot of red did come out, which means it was was mixed with some green. It was probably flushed the first time on a green machine, then a red machine the second time, but not enough with the two heater cores, etc.

He said that spent a lot of time thoroughly flushing out any green and used 4 gallons of red in the process. They also cleaned out the overflow bottle.

At this point I'm satisfied it was done properly. I'm also very happy with the way the manager of this service department stepped up to the plate and went the extra mile to make this right. They no doubt lost money on this deal, but didn't give me one bit of hassle when I complained and made darn sure it was done right this last time.

It pays off to treat customers right. If I ever need a Toyota dealer again, I'll go back to them.

Thank you for all your advise and for the offers of help out there. I do appreciate it.
 
Back
Top Bottom