Diff issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 2, 2015
Threads
30
Messages
637
Location
Valley Springs, CA
So I'm working my towards my destroyed front ring and pinion and the first thing I find is the lower mounting bolt on passenger brake caliper is missing. Could this have caused uneven braking and ruined my diff? I had just done a full rebuild of front axles and brakes before a 3000 mile road trip, with plenty of locker use in the snow, led to this. Did I kill my front diff with a botched torque job?
 
I don't think there is any way in hell a loose caliper led to a broken ring and pinion. The hub doesn't wobble as it is held on using the 54mm adjusting nut. Uneven breaking is annoying, but I can't think of any mechanism where it would damage the R&P. How much fluid came out when you drained the axle?
 
Is the ring and pinion definitely no good?

I lost a lower caliper bolt on mine. The breaking force pulled the caliper outward so it rubbed on the inside of the wheel rim.

Mine came out on a road trip 800 km from home. I was so sure I'd blown the front R&P, was noise, vibration grinding sensation etc

I pulled the front shaft and drive flanges in the pouring rain, locked the CDL to limp it home only to have the caliper grinding on the rim at the first stop sign :mad:
 
I don't think there is any way in hell a loose caliper led to a broken ring and pinion. The hub doesn't wobble as it is held on using the 54mm adjusting nut. Uneven breaking is annoying, but I can't think of any mechanism where it would damage the R&P. How much fluid came out when you drained the axle?

The appropriate amount of gear oil came out of the diff and it had just been changed before the trip.

Is the ring and pinion definitely no good?

I lost a lower caliper bolt on mine. The breaking force pulled the caliper outward so it rubbed on the inside of the wheel rim.

Mine came out on a road trip 800 km from home. I was so sure I'd blown the front R&P, was noise, vibration grinding sensation etc

I pulled the front shaft and drive flanges in the pouring rain, locked the CDL to limp it home only to have the caliper grinding on the rim at the first stop sign :mad:

Ima pull the other axel in an hour or two and we will see the innards of the diff then. Im pretty dang sure it's toast because after lifting the front you can try to spin the front wheels and the drive flange moves in and out of the carrier about a half inch and there is a grinding noise. I did not service the diff itself when I did the birfs, other then change the oil. As a note the driver side oil seal had failed prompting the service in the first place.
 
So inbetween working I have been going out there as much as possible. I got the axels out and need to remove the locker actuater but I dont understand hot to remove the tube without damaging it. The FSM just says remove it. The FAQ doesn't mention it at all. And this Repairing Differential E-Lockers thread doesn't tell me either so obviously my noobness is causing some major disconnect here. Help!
 
So inbetween working I have been going out there as much as possible. I got the axels out and need to remove the locker actuater but I dont understand hot to remove the tube without damaging it. The FSM just says remove it. The FAQ doesn't mention it at all. And this Repairing Differential E-Lockers thread doesn't tell me either so obviously my noobness is causing some major disconnect here. Help!


Per the Diff locker repair linked article:
Bottom pg2 / Top pg3 - engage/confirm the locker is locked for clocking purposes, pull bolts & remove actuator.

Seems about the reverse of when I bolted together my e-locker conversion.

IIRC the rear is the one you had to pull the shift fork for the dog/cuff gear via the inspection plate, the front just comes out in a single piece. easy peasy, lemon squeezy
 
Lock diff, pull actuator if that's the goal.

Otherwise it's lock diff, pull burfs w/ the inner axle - remove the 3rd member as a whole.

It sound like you're trying to get your gears back out, so yes to pulling the diff as a whole once you pull the birfs/inner axles.
 
Yeah, I'm w/ @mudgudgeon here. - All I recall were the postion sensor & actuator power plugs, then break the torque on the ~4 bolts on it, run a quick gasket scraper in there if you have FIPG sealing it.

Help me out here, hate it when that early onset senility raises its' head.
 
Help me out here, hate it when that early onset senility raises its' head.

I'll help you out, it's definitely early onset senility, but there's a cure. Amputation 1 1/2" below the chin. :hmm: thank me later :hillbilly:

There's a small breather tube wrapped up in the wiring harness. No other tube I can think of.
 
Haha - I thought of that tube, seemed to remember it in the rear harness, & the connectors for it in the floor/intermediary in RR.

I wasn't going to go full hog / stake my life it ran to the FR actuator too, so glad you jogged my hazy memory of it in the FR as well.

Dam you, senility. Dam you.
 
Back
Top Bottom