Degrading starting performance

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 6, 2007
Threads
120
Messages
1,755
Location
Under the hood
Maybe my search-fu is weak, but I haven't been able to find this issue in the archives.

As long as I have owned my '93 it has had a long start time (call it 1-2 secs of starter turn before the engine fires.) I was having problems with my bendix sticking, so I rebuilt my starter a few months ago (2.2kw). That cleared the bendix problem and I got slightly improved starter performance. Then for something totally unrelated I pulled my plenum and cleaned it all up and put in rebuilt injectors and new plugs.

For a few brief, glorious days I got instant starts. Not kidding, I barely turned the key and the truck fired. Over the last 4-6wks though the start performance has slowly degraded, and now I get really slow starts. I have to hold the key for 3-4 secs and there are many rotations before the truck fires. Some of the rotations feel sluggish, like its not catching entirely.

I have good battery, I changed my fusible links, and my connections look clean and good. I'm running out of ideas.
 
It is possible the fuel regulator is not holding pressure at the injectors?


regards

Dave

my first thought was a fuel problem, but i have no leaks or visible loss. pressure regulator is a great thought. ill see if there is a way to test it.
 
I have very little experience on the 80 petrol engine but, most fuel injection systems hold pressure via a regulator and control it by letting excess return to the tank, so a leak would not necessarily be visible. Having said that, most systems run the fuel pump for a few seconds prior to cranking, it might be worth switching on the ignition and allowing the pump a few seconds to pressure up the system. If the engine starts better then it may help with the diagnosis?

regards

Dave
 
There needs to be some sort of fail safe on the fuel pump logic. If the engine is not running, the fuel pump should not run.
That being said, I am certain that the fuel pump on a 3FE only runs when the starter is cranking and when the AFM intake flap opens. However, the 1FZ-FE is still new to me and I am learning as I go along. The fuel pump logic is different as it is controlled by the ECU, but in the event of an accident and motor stall, the FP must shut down. I doubt that the FP runs when the key is in the ON position without the motor running.

What keeps the fuel rail pressurized after the motor shuts down is a check valve in the fuel pump. This is a known issue on a 3FE with a bad FPR.
 
Cheers @jonheld, tks for pointing me towards the check valve. I have seen quite a bit of discussion on the forum from folks I respect about whether or not the pump is active before the engine is running.

I found this in the FSM on how to check the fuel pump:

1) Using SST, connect terminals +B and FP of the DLC
2) Turn the ignition switch to ON
3) Check that there is pressure in the hose from the fuel filter

When I look at the EWD it shows that +B is switched power (I think) and if you bridge that to FP then you are bypassing the Circuit Opening Relay, the fuel pump relay and the fuel pump resistor. I believe that implies those circuits are preventing the pump from running when the key is in the ON position but the engine is not running. I'm not an EE and I didn't design the system, but that's my interpretation.

I also found in the FSM that if the system doesn't hold pressure for 5 mins (21psi) then the following items are suspect:

1) fuel pump
2) pressure regulator
3) injector

I couldn't find anything in the FSM on a check valve, including in the pump diagram? Can anyone point me to where said check valve is?
 
As I said I am unsure, every other FI system I have worked on runs the fuel pump for a few seconds as the ignition is switched on. Once the engine is cranking the fuel pump runs, if the engine does not start then the pump stops. If the engine runs and the key is released then the ECU keeps a feed to the pump, if the engine stops then so does the fuel pump, an accident for example. Many modern vehicles also have an impact sensor that shuts off the fuel in the event of an accident for example, either way it is important that pressure is held at the injectors on any FI engine in preparation to start.

regards

Dave
 
As I said I am unsure, every other FI system I have worked on runs the fuel pump for a few seconds as the ignition is switched on. Once the engine is cranking the fuel pump runs, if the engine does not start then the pump stops. If the engine runs and the key is released then the ECU keeps a feed to the pump, if the engine stops then so does the fuel pump, an accident for example. Many modern vehicles also have an impact sensor that shuts off the fuel in the event of an accident for example, either way it is important that pressure is held at the injectors on any FI engine in preparation to start.

regards

Dave
Agreed. I don't know the specifics of how the ECU runs the fuel pump and if in fact it "knows" the sequence of events. This is primarily a guess on my part based on 1986 technology. The 1FZ ECU is 1989/90 so certainly not "advanced" by any standard.
 
I installed another FPR I happened to have laying around (used, pulled from a good/running motor but history unknown) and had no change in starting performance. Leaving the key in the ON position a few seconds before starting doesnt seem to help.

Im getting the best mileage Ive ever gotten, so I dont think Im leaking through an injector, but not sure how I could check that.

Any help on location for the check valve? I havent been able to find anything on it in my searches.
 
I installed another FPR I happened to have laying around (used, pulled from a good/running motor but history unknown) and had no change in starting performance. Leaving the key in the ON position a few seconds before starting doesnt seem to help.

Im getting the best mileage Ive ever gotten, so I dont think Im leaking through an injector, but not sure how I could check that.

Any help on location for the check valve? I havent been able to find anything on it in my searches.
The check valve is part of the fuel pump and not an individually replaceable part.
Statements like, "Im getting the best mileage Ive ever gotten" makes me think she's running a bit lean, but again, that's a guess.
Have you changed the inline fuel filter and the fuel pump pre-filter?
 
The check valve is part of the fuel pump and not an individually replaceable part.
Statements like, "Im getting the best mileage Ive ever gotten" makes me think she's running a bit lean, but again, that's a guess.
Have you changed the inline fuel filter and the fuel pump pre-filter?

The in-line fuel filter was replaced as a part of the intake plenum work I was doing (along with injectors and plugs.) The 'best mileage' is consistent I think with the work I did, I picked up ~1mpg (very consistent across multiple tanks) after cleaning the plenums, replacing the fuel filter, installing rebuilt injectors and new plugs. i.e. its about what I would have expected after doing that type of work.

Bummer about the check valve, I was hoping it was a separately serviceable part. Not sure I am in a position right now to replace a bunch of parts and hope that one of them does it.
 
Not sure if this helps, but its cooled off significantly lately, and the truck is back to firing instantly. I have another used OEM pump en route, so thats still on the list to do, but I cant figure out how the outside temp would affect this?
 
I understand there is a slight debate on fuel pump starting times. I agree many manufactures start the fuel pump b4 start. Toyota efi systems do not. They rely on a start signal from the ecu...
The ecu uses the air temp to help adjust the fuel/air mixture during start and injector pulse duration. It uses 68 degrees as a standard day and increases/decreases as needed.
 
Back
Top Bottom