Control Arm Skids?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

TOY350

#1 Super Guy
SILVER Star
Joined
Aug 19, 2004
Threads
182
Messages
3,619
Location
Grants Pass, OR
Has anyone produced skid plates for the rear control arm frame mounts? I know Wild West Offroad was going to get some going but don't know if it ever happened. All Pro has them for the FJ but I didn't see any for the 80.

Seems these rear mounts take quite a bit of abuse and I am imaging mine will on the Rubicon this year. I have already banged them up a bit running the McGrew. I do a lot of work on my 80 but I don't fab or weld so I'm left looking for some to buy.
 
I wouldn't worry about the frame mounts, they will hold up (trust me...). I would weld some 1.5" angle to the bottom of the control arm itself to keep it from bending.

Thanks Chad,

I figured they could take some abuse since I have hit them pretty hard but wasn't sure after working on a FJ this weekend and seeing his bracket bent up to the point he needs to take off the arm and bend the bracket back in place. Understand the angle iron protection, I will look into doing that before June.

Garett
 
I'm really curious about this... If someone makes soem I'd like to get them, if not, I'm making some before my next trip... this is just one trip's worth of damage (more than I'm comfortable with):

dsci1880.jpg


Albiet, not the best pic, but you get the idea...
 
Here are mine:

100_9163.jpg


After bending both the stock ones, this was a necessary (and cheap) mod. Highly recommended.
 
OH I bent one up good on the 'con and had to replace it. Thanks to fellow Cruiser fanatic Andy for the replacement! I have mine reinforced with some thick tubing that was line torched in half and welded to the bottom side of each. It doesn't help the bracket at the frame which still could use skids for sure. Beno you make yours or what?
 
Uh....looks like a piece of angle iron just resting on top of a control arm...held on with gorilla glue?

:flipoff2:

The only photo I could find was just before the welds were done.
 
The reason to do this is to stop getting hung up on those mounts - they are *the* hangup point on the 80 during crawling. My sliders have made a big difference both in not getting hung up as well as reducing abuse on the arms themselves.

Have a shop weld something up for you - you aren't going to get a bolt on solution so there is no real reason to try and buy anything pre-fabbed. This is just some 1/4" plate.
LCA Mount Sliders.webp
 
Here ya go Garett....

not really being produced by anyone other than bored mudders in the garage :D but a couple ideas
https://forum.ih8mud.com/80-series-tech/274058-rear-control-arm-mount-ramp-sliders.html

The reason to do this is to stop getting hung up on those mounts - they are *the* hangup point on the 80 during crawling. My sliders have made a big difference both in not getting hung up as well as reducing abuse on the arms themselves.

Have a shop weld something up for you - you aren't going to get a bolt on solution so there is no real reason to try and buy anything pre-fabbed. This is just some 1/4" plate.

Thanks, that was the stuff I was looking for. I was orignally just going to reinforce the original shape, but I like this "slider" approach. Thanks again!
 
I'm really curious about this... If someone makes soem I'd like to get them, if not, I'm making some before my next trip... this is just one trip's worth of damage (more than I'm comfortable with):

dsci1880.jpg


Albiet, not the best pic, but you get the idea...


Those aren't bent, they still have corners.:meh::rolleyes:

Those things are sturdy, if you can't get a skid, just beat them until you have clearance.:hillbilly: The angle iron or retube on the control arms is recommendable.:cheers:
 
well its managed to fold itself in and start contacting the LCA... sturdy yes, but able to hold up to my wheelin, no.

and that pic was before the end of the day....

on the mounts, is it better to build a little slider out of square tube for plate as some have show, or replate the mount thus keeping allowing the tire to contact sooner?
 
IMHO the angle iron just looks like an ADHOC, quick fix. My thoughts would be to make a jig so the OEM control arm length can be maintained, cut the control arm in half, sleeve it with tubing that has the same ID as the control arms OD of your desired wall thickness, drill multiple holes along the sleeve, weld it at each end around the stock control arm and plug weld all the holes. Have not done this myself, but is the route I would/will take.
 
Back
Top Bottom