CO2/Air Tools

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 13, 2006
Threads
48
Messages
322
Location
Where the glaciers stopped.
I have searched to no avail. And I will post this in the tool section as well, but that area does not get many visitors.

My question; I have a 20# CO2 set up and now I need to know if there are special air tools I should get to work with the system or will any impact wrench that is rated for auto-duty work do the trick?

Please educate me on this - I have a Sears gift cert burning a hole in my pocket. Thanks and Merry Christmas!!!! :bounce::bounce2:
 
Any standard air tool will work. The only possible issue with CO2 is that it's colder and the tool will have a greater tendency to freeze up on long tool runs. Probably not an issue for a limited use trail tool.
 
Like Tools said, unless you are running a cutoff tool or doing a 4 tire change pit stop, it should not be an issue. I have a Central Pneumatic gun in my tool box for wheeling. I have Sears at home. The other thing is that if you use it heavily you will have to stay vigilant with oiling your gun. CO2 will dry it out. What regulator are you using? This will freeze up if you do not have one rated for high flow high pressure liquid. Just airing up tires slows plain regulators down and eventually destroy them.
 
Like Tools said, unless you are running a cutoff tool or doing a 4 tire change pit stop, it should not be an issue. I have a Central Pneumatic gun in my tool box for wheeling. I have Sears at home. The other thing is that if you use it heavily you will have to stay vigilant with oiling your gun. CO2 will dry it out. What regulator are you using? This will freeze up if you do not have one rated for high flow high pressure liquid. Just airing up tires slows plain regulators down and eventually destroy them.

I am using a hi-flow regulator from powertank. Thanks for the heads up on the extra oiling required with CO2. Do you use the Central Pneumatic (less quality than Sears I presume) on the trail because it gets tossed around more and is more likely to break?

Thanks a lot for the feedback.
 
Don't know what pressures you plan on running, but cheapy air tools don't handle higher pressures as well as quality ones.

I run my Chicago Pneumatic and IR tools off of my 150 psi C02 system with no problems, but I've damaged a few lesser tools at that pressure.

Co2 won't "dry" anything out more than air will. A couple of drops of air tool oil before each work session will keep the tools running well.


Adam R
 
I'm not sure if this is a no-brainer or not, but do you guys use your CO2 setup as a fire extinguisher as well. Seems like all that would be needed is setting up the regulator and a high volume, wide spray air nozzle.
 
If you plan on using air tools frequently, get a second tank. air tools use CO2 really fast, you can use up a tank fairly quickly. 20# is a good size tho for occaisional use
 
My tank is actually a converted fire extinguisher, that just happens to be the same size and made by the same manufacturer as a Powertank. For $52 filled and re-certified, it was a no-brainer, especially after I sanded the red paint off and polished the aluminum a little.

I use the Powertank bracket and a simple 150 PSI spring valve from the Williams Balloon Company for a regulator. While not adjustable, it flows really well for re-setting beads and running air tools. I could always run an adjustable regulator in series if need be.

As for using it as a fire extinguisher, yes you could, but to be effective, I would need to turn my tank upside down and have it expel liquid Co2 vice gaseous. The liquid will instantly turn to gas when it exits the tank. I don't think you'd get enough C02 gas on the fire quickly enough to make a difference if you were just blowing on it with an air hose.

I did a quick test once and keep this idea in the back of my mind for one of those "what if" scenarios I hope to never run across.

Adam
 
You will also want to turn Down the PSI output when you run your air tools. 120+psi is not necessary IMO 80 is plenty, but others might disagree. Just one of the things I was told.
 
This is all great info. Thanks!

Re-cap w/ a couple more questions:

80 psi should be all the pressure I push through the air tools if I want them to last. Question; If I come across a tough nut that doesn't want to move, will turning up the pressure on my regulator increase the drive output on my gun?

Any high quality gun will work.

Should start out with a 1/2" drive for the garage then get a 3/8" for the trail. Why not just take the 1/2" on the trail (size?)?

Oil my gun all the time.

Anything else a rookie air tooler needs to know when working off CO2?
 
This is all great info. Thanks!

Re-cap w/ a couple more questions:

80 psi should be all the pressure I push through the air tools if I want them to last. Question; If I come across a tough nut that doesn't want to move, will turning up the pressure on my regulator increase the drive output on my gun?

Most tools are rated at 90psi for max life and performance. Many users run them at higher pressures, they will make slightly more power at a cost of reduced life.

Any high quality gun will work.

Should start out with a 1/2" drive for the garage then get a 3/8" for the trail. Why not just take the 1/2" on the trail (size?)?

For impacts, I prefer Ingersoll-Rand, good stuff. I use the 2112 & 2115 3/8" guns as my primary gun, because they are lighter, smaller and preform well, only breakout the bigger guns when needed. If I had to choose one gun it would be a 231 if on a budget, or a 2135.

I carry a 2115 on the trail because of the size, they consume less air and they hit ~300 ft-lb. A few years ago that was what 1/2" guns hit.

Oil my gun all the time.

Anything else a rookie air tooler needs to know when working off CO2?

CO2 is dry, for an air tool this is a good thing moisture kills them. So just oil normally, if the toll is run too long and it freezes up, just allow it to thaw.
 
As for using it as a fire extinguisher, yes you could, but to be effective, I would need to turn my tank upside down and have it expel liquid Co2 vice gaseous. The liquid will instantly turn to gas when it exits the tank. I don't think you'd get enough C02 gas on the fire quickly enough to make a difference if you were just blowing on it with an air hose.

I did a quick test once and keep this idea in the back of my mind for one of those "what if" scenarios I hope to never run across.

Adam

Gaseous Co2 works perfectly well to extinguish a fire. A friend of mine lit his engine bay on fire (in my brand new shop) when he was turning the engine over to clear water from the cylinders. There was oil everywhere, and the fuel injectors were still working, spark from somewhere and damn if he didn't have a 6 foot high bonfire. What to do, what to do? I hadn't gotten around to putting in an extinguisher (but I did the next day) and there was no water hose handy (thank God- that would have probably made it much worse). He looked around in a panic and saw his Co2 tank sitting next to his truck, hooked up an air nozzle, and blew it right out. Instantly, from what he told me. Then he proceeds to call me at work and share his story- I heard 'fire' and just about s*** myself, but in the end it worked out. Cooked some wire loom and the hood insulation.

In short, if you carry Co2, don't hesitate to use it on a fire. Have the air hose and blower nozzle handy too.

I would think that if the liquid Co2 gets into the regulator or air nozzle, it would freeze. Co2 extinguishes fire by displacing the oxygen from around the flame, and without oxygen *most* fires can't burn. It doesn't take a huge volume of Co2 to displace the oxygen at the base of a fire.

-Spike
 
Agree, blowing on a fire with an air hose can put a fire out, no argument there. But if you had a fire of any significance, it would be hard pressed to put it out at 8-10 CFM via an airhose.

A Co2 fire extinguisher operates by expelling liquid Co2 that does an instantaneous phase change to gaseous Co2 when it exits the nozel and now finds itself in atmospheric conditions. You can empty a 10 lb Co2 extinguisher in less than 15 seconds. It would take you much, much longer to empty a 10 lb tank through an air hose.

Co2 is also suppressing the fire via two methods, robbing the fire of an oxidizer, oxygen, and by rapid cooling due to the phase change mentioned above. The airhose method minimizes the volume and pretty much negates the cooling after it travels though 25 feet of hose.

I was careful to specify that with my valve/regulator that I can turn my tank upside down and expel liquid Co2 without problems. I'm not sure how a Powertank regulator would handle this, but I'd suggest practicing to see if it would work.

With my set-up, I can get a huge blast of Co2 that would knock down a lot of fire in a hurry.

Again, this is one of those secondary uses of a tool you happen to have with you. A dry chem extinguisher is also a good idea for any vehicle.

Adam
 
Back
Top Bottom