Check Engine light...saga continues....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 13, 2004
Threads
130
Messages
654
Location
Sacramento Ca.
I have posted about this issues prior to this but, this time I am confused beyond doubt. Here is the detail. My rig is a 1993 FZJ80 with 270k. I have been throwing the codes 83, 84, 85, and 28. This has been going on for well over a year. Anyway, I have the newer ECU (89661-60221) and not the old style (89661-60170). So, this throws out the idea of having the issues with the early style. Today I went and replaced both 02 sensors since it hasnt been done in a long time. Oh yes, last week I cleaned the TPS and the MAF. After doing all of these items I pulled the 15amp EFI Fuse to clear the codes. I waited a few minutes then put it back in, but the light still remained on. So, today after putting in new 02 sensors, I pulled the Main EFI, the 15am EFI and then the Neg. on battery................still, the light stayed on. It never reset, nor turned off. :mad:

I am at a loss. Does anyone have any idea or suggestion what I should do/check next? I am seriously pissed at the moment!!:mad: :censor: :mad: :censor: :mad:


Thanks for any advice on this matter and please, feel free to suggest anything you think might help:frown:
 
So, the light was on even with the battery cable unhooked? If so I'd trade it in.


It seems unlikely, but I'd start by swapping out a known good ECU.
 
So, the light was on even with the battery cable unhooked? If so I'd trade it in.


It seems unlikely, but I'd start by swapping out a known good ECU.

When the battery is unhooked, the light is off but, as soon as you re-connect it, the light is on. There is no delay for the light, no nothing. Its like it wont reset!!

As for swapping out a known good ECU, well, that could happen but, I want to exhaust every effort first.

Anoyone else have any ideas?:confused:
 
I would be reluctant to mess with the air flow meter. Have you checked the wiring harness for the 02 sensors? Its stange that replacing those didn't clear the 28.

I too would suspect a wiring issue. If the code comes right back on with no delay then I would suspect an incomplete circuit to all the components that the codes are related too. My next step would be to use a continuity checker on the wires going to the O2 and the VAF. I would check for continuity to the ECU from the compoent. That means a bunch of pouring over wiring diagrams to figure out which wire is which.

Another way is just to phisicaly trace them and look for breaks. Not as good but it may work.
 
I had a code 28 with new sensors. It was throwing the code due to the truck running too rich. The airflow meter was allowing this due to the spring being loosened over time. its a simple fix with the 93-94 afm design

With this problem he would have to run the truck in order to throw the codes. His codes come right on after battery hookup.

Checking the wiring is a good idea, but kinda labor and time intensive. I'd see if somebody local will let you use their ECU just to eliminate it as a cause so that you don't spend all that time checking wiring only to find out it was the ecu in the first place.
 
Thanks for all the replies. I am off to check/search out if I have a wire that is lose or severed off some place. Also, just for the hell of it, I am going to check the codes again, just to see if anything new has come up since driving it this morning.:rolleyes:
 
GREAT....................................................The good part is all the previous codes are off:)

The bad part is, now I am getting a code 26! I have been reading up on it and its due to an overly rich air/fuel ratio. So, anyone have ideas on what to attack first? Anything you might have come across as to what to check?

Thanks for all the help and hopefully I will get this damn check engine light to turn off today!:rolleyes:
 
Everytime my truck has need new O2's it has thrown a code 26. I would still check the wiring and connectors. Also, have you checked the intake tube that runs between the VAF and throttle body? One time my clamps were loose on that and it indicated a code 26. It can also crack.
 
Everytime my truck has need new O2's it has thrown a code 26. I would still check the wiring and connectors. Also, have you checked the intake tube that runs between the VAF and throttle body? One time my clamps were loose on that and it indicated a code 26. It can also crack.

Its a brand new tube but I will check for leaks and clamps. I am taking another persons advice and ditching my K&N filter for a stock one today. Hopefully that will help it out. Who knows though. Thanks for the advice and keep it coming if anyone has anymore.:beer:
 
If it throws the code before you run the truck it still points to a wiring or O2 sensor issue because it can't tell lean from otherwise if you have no combustion.
 
From the FSM for codes 25 and 26.

These codes should only be triggered by a running vehicle. I think your wiring may be gooned up somewhere, but I hope not.
Good Luck

(1) Heated oxygen sensor output
at 2,000 rpm is less than 0.45 V for
at least 90 seconds when¿warmed
up. Applies only to
code 25 and for California
models, excepting high-¿altitude
areas.
(2) When the engine speed
varies¿by more than 15 rpm over
the¿preceding crank angle period
during a period of 30
seconds¿during idling with the
intake air,
¿temp. 0C (32F) or above.
(3) When the difference between
the air-fuel ratio feed back compensation
value of the front¿and
rear exceeds 15% of the¿two
values in a period of 10¿seconds
while the engine
speed is 2,000 rpm or more
and the engine coolant temp. is ’
between 70C (158F) and
95C (2030F). ’
*6 (2 trip detection logic) (1) - (3)


Trouble area:
Engine ground bolt loose
Open in E 1 circuit
Injector circuit
Injector
Fuel line pressure
ECT sensor
Compression pressure
ECM
 
Went to Toyota today and purchased a new air filter and ditched the K&N. I heard this might be causing the code 26. Well, when I got home I installed the filter then ran the cruiser for a bit. I proceded to check the codes and what would you know..................................THE ORIGINAL PROBLEM IS BACK!!! So, let me recap, I was getting codes 28, 83, 84, 85 then those finally cleared up (new O2 sensors helped) and in return code 26 came about. Lets not forget that this has all been going on within the last 24 hours. Anyway, now, code 26 is gone and the original 28, 83, 84, and 85 are back! :mad: :mad:


I have decided to put the cruiser to rest, and not sure for how long. I am over the damn thing at this point!! (ok, thats a lie, just going to stop working on it for a day or two);)

Sooo, if anyone has some input please let me know. Thanks to everyone so far, I have been checking and looking at whatever you guys and gals thought it could be.:beer: :beer:
 
I would really consider trying a known "good" ECU. If you have a buddy with a 1993-94, see if they will loan you thiers for an evening and give them your ECU if theirs throws no codes. ;-) (j,j) ECU's aren't that expensive. I paid $250 for mine, used. Those are the some codes mine threw before the ECU replacement. It was worth it to me,just because the Check Engine light really drives me nuts.

TK
 
I would really consider trying a known "good" ECU. If you have a buddy with a 1993-94, see if they will loan you thiers for an evening and give them your ECU if theirs throws no codes. ;-) (j,j) ECU's aren't that expensive. I paid $250 for mine, used. Those are the some codes mine threw before the ECU replacement. It was worth it to me,just because the Check Engine light really drives me nuts.

TK


I am going to search around and see if anyone local might let me try their ECU for an hour or so. Damn, all I want is for that BRIGHT CHECK ENGINE LIGHT to go away!!:crybaby:
 
Back
Top Bottom