CDL Questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I think I got it (the cdl only engages in 4lo otherwise) and see there’s no reason not to install it.

Thanks, received the switch today and will try it this weekend!

Yes.
Sometimes you want to have the CDL engaged while in 4HI and you cannot do it without the controller/button.
Sometimes you want to disengage the CDL while in 4LO and you cannot do it without the controller/button.

Make sure you follow the instructions for the footwell module.
 
I know this is an old thread guys, but wanted to clarify.

When they say there’s no ABS, does that mean with the CDL installed or when the button is pressed?

If I understand correctly, the pluses for installing the CDL is to prevent wear on the VC from potentially destroying itself from heat and also to better fuel economy.

The reasons for not installing is to preserve all the advantages of AWD (works in high traction surfaces like paved roads and intermittent ice patches)...do I understand that correctly?



Thanks, Rick
The reason it turns off the ABS when the CDL is locked is because the wheels sensors can sense different tire rotations and there becomes a problem because now the driveline is locked together front to rear. Driveline braking is possible if one rear wheel is locked, it will "apply a resistance" to all four wheels through the driveshaft and axles. ABS and driveline braking do not get along and it will break axles, shear off driveshafts, and cause loss of control of the vehicle.
 
I think I got it (the cdl only engages in 4lo otherwise) and see there’s no reason not to install it.

Thanks, received the switch today and will try it this weekend!
You'll want to do the pin 7 delete for full control of the CDL. With the pin 7 mod, only you control the CDL - it won't automatically engage in 4lo anymore. It will not lock in 4hi or 4lo unless you push the switch. The instructions are on the Slee site here. Just remember with this mod, you control the CDL and ABS with the switch. IIRC, if you exceed 45 mph with the CDL locked, you will need to stop the vehicle, turn off the CDL and turn the engine off and then back on to reset the ABS (turn the ABS light off). Most people consider ABS to be a PITA, so it's not a big issue, but it's good to know if having the ABS light on bugs you.
 
Last edited:
You'll want to do the pin 7 delete for full control of the CDL. With the pin 7 mod, only you control the CDL - it won't automatically engage in 4lo anymore. It will not lock in 4hi or 4lo unless you push the switch. The instructions are on the Slee site here. Just remember with this mod, you control the CDL and ABS with the switch. IIRC, if you exceed 45 mph with the CDL locked, you will need to stop the vehicle, turn off the CDL and turn the engine off and then back on to reset the ABS (turn the ABS light off). Most people consider ABS to be a PITA, so it's not a big issue, but it's good to know if having the ABS light on bugs you.

Thanks everyone, was able to complete my first mod this weekend, tho the wood grain trim snapped in 3 places to get the switch to mount flush where the security button once resided.

Incidentally, I noticed my air conditioning didn’t work afterwards tho the AC light turns on (just blows ambient temp)...is this a coincidence, you think, or could I have managed to mangle something in the process?

Am going to do the pin 7 mod this morning, hopefully it’s not a give & take arrangement there, lol.
 
......................Incidentally, I noticed my air conditioning didn’t work afterwards tho the AC light turns on (just blows ambient temp)...is this a coincidence, you think, or could I have managed to mangle something in the process?...............
Might be a coincidence, but I doubt it. I'd 1st check connections as @Dragos80 suggests. When did you last use your A/C? Being as it's early for hot weather, I'm guessing several months ago. Was it strong last season?
 
Yep, checked the connections...have gotten easier to get behind the dash now.

I picked up the rig in Feb/March but the defrost worked okay here in New England.

I eventually tried the CDL btw and the 7pin mod worked, much to no ones surprise but mine, lol.

This is my first 4x4 vehicle that has the manual transfer case...the closest I got was when I owned the first gen Durango but never had a reason to shift out of AWD.

The transfer knob was incredibly notchy. There were whirring gear/grinding noise as I shifted between H and L from neutral while the transmission was in neutral as well. It’s all better now and I’ve gained more confidence between the different 4wd options today.

Might be a coincidence, but I doubt it. I'd 1st check connections as @Dragos80 suggests. When did you last use your A/C? Being as it's early for hot weather, I'm guessing several months ago. Was it strong last season?

image.webp
 
Yep, checked the connections...have gotten easier to get behind the dash now.

I picked up the rig in Feb/March but the defrost worked okay here in New England.

I eventually tried the CDL btw and the 7pin mod worked, much to no ones surprise but mine, lol.

This is my first 4x4 vehicle that has the manual transfer case...the closest I got was when I owned the first gen Durango but never had a reason to shift out of AWD.

The transfer knob was incredibly notchy. There were whirring gear/grinding noise as I shifted between H and L from neutral while the transmission was in neutral as well. It’s all better now and I’ve gained more confidence between the different 4wd options today.



View attachment 2294357
Congrats on the CDL and pin 7 success!

I would have freon checked at a svc center you trust. You also might try selecting the far left button on the top row and take it off recirculate (middle row, right button) to see if there's any difference in output air temp. I doubt if that makes a difference, but it's worth a try. Also, be sure your heater valve is closed and matches the slide temp indicator on your heat controls. That valve is in the top center of your firewall on a hose. Have some one slide temp control while you watch it move.

On your transfer case, when shifting between hi and lo be sure throttle is at idle. If you stay in neutral for very long with engine running, sometimes gears in transfer case will move slightly and then shifting out of neutral will grind just a little and that's normal. It's not recommended to leave transfer case in neutral unless you have a specific purpose, such as having your rig flat towed. Remember, if your T/C is in neutral, the only thing that will secure your rig while parked is your emergency brake or your regular brakes. Park on your tranny will not hold you anymore until you shift T/C out of neutral.
 
Back
Top Bottom