Carburetor WTF???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 16, 2006
Threads
166
Messages
620
Location
Tulsa, OK
Carburetor WTF??? Puhleeease Help.

Okay, I posted a while back about the Weber 34/34 (new) I installed on my 78 FJ40 w/2F.

I had mentioned that the fuel line is building hellacious pressure at the fuel inlet, but not leaking.

The cruiser has been on jack stands for a month so I haven't driven it, but I have started it on occasion to keep it lubed.

I started it the other day, let it idle and opened the hood to inspect things (I haven't gotten to wrench on the cruiser much lately).
Long story long, fuel was spraying out the sides of the hose at the fuel inlet on the carburetor, due to EXTREME pressure.

The fuel line is the right size, the clamp is snug, what the crap is going on?

I have always wondered if not having a return line from the carburetor would make the difference...


POSSIBLE THOUGHT:just came to me...

Recently removed the fuel tank-consequently all of the fuel lines were disconnected. Is it possible that a hose in the wrong place at the fuel tank could cause this pressure issue? Seems likely.

Thanks.
 
Last edited:
Pin head-Its a mechanical fuel pump.

Good point on the fuel lines...:doh:


I just can't figure it out. I really can't say how it runs under a load until I get the axles mounted.

I can say that it starts relatively easy (pump gas pedal 2-3 times first) and runs for a half-second then dies, then starts easy again (after pumping gas pedal again) and seems to run fair.

Now that I think about it I believe there was some white smoke out of the exhaust (but I couldn't really tell cause it was like 3 degrees outside). -Running rich? or burning oil?

Any help would be appreciated...

I bought this carb for over $300 and haven't been able to get it right yet. Every other Weber I have done (32/36 & 38/38) on my other cruisers were a breeze.

Thanks
 
Could there be some reason why the fuel pump is allowed to pump too much fuel?

It seems that if there was no pressure relief on the fuel tank (lines) it would be limited in the amount of fuel it could transport (a vacuum is created), but if there is no internal vacuum in the tank it would be able to pump more freely?

Just a theory...

What do you guys (and girls) think?
 
Anyone?

What if I said that the cruiser is on a treadmill?
 
Then the thread would take off....but you have to post a poll about it.

(sorry, no real help here!)
 
Lotsa people run the stock mechanical pump with no fuel return line and they don't have the problems you describe. The possibilities are that the fuel line connections are not good or the pump itself is putting out too much pressure. How about putting a gauge on the pump outlet? I think the pressure is supposed to be 15-20 PSI (or whatever it says in the FSM).
 
Some of the earlier rigs had no fuel return line. Many aftermarkt installations have no return line (99.999% of Webers, Holleys and any brand of 4bbls). After a certain point the pump will not build any more pressure. WAY WAY below what it would take to force fuel past a properly connected fitting. Lack of a return is almost certainly not your problem.

Be careful about assuming that you have high pressure. It only takes a few PSI to create quiet a fountain.

My first assumption is that your fitting is damaged or has debris in it or some other condition which is keeping it from sealing, regardless of how tight you get it.

Depending on exactly what type of connection you have... Make sure that the fitting is not bottoming out before it actually snugs the line down to seal.


Mark...
 
Not a carb expert, but I'm running a DGAS38, and have spent a lot of time getting it to run right...

A couple things I noticed in the list of posts...

You said you've run the 32/36 and the 38/38 before successfully, but this one is a 34/34?? I've not heard of that one, should it work?

You said that it starts easy, runs a few moments then dies, then starts easily again. That is usually a symptom of a restriction. When the engine is not running, the bowl fills, but with the engine running, it burns off the gas faster than it is coming into the bowl, so it runs dry, and the engine dies, which allows the bowl to fill again. Maybe you have a restriction on the inlet, there is probably a filter there in the carb.

Also I would have to look it up in the Weber books, but I think you are not supposed to more than about 3 or so PSI on the inlet. I have a pressure regulator on mine, and it is set to 3.5. As long as it over 2.5 I can drive up a long hill without it hesitating.

As far as I know, nothing in the carb will increase the pressure in the fuel line, that would be the fuel pump's job. When ever the bowl is full, the needle valve should be closed, stopping the flow of fuel. So the fuel pump seeing restriction from the needle valve should be a standard operating condition. I would put a pressure gauge on it to see if the pressure is unusually high or if the fitting has unusually low grip. You may also want to consider an in-line pressure regulator.

gary
 
Do you have the correct sized fuel line for the fitting? Fitting cracked? I've seen folks using old fuel line that was deteriorated on the inside causing particles to plug up the inlet, or cause the needle valve not to seat.
The very short period I used a weber, I found that it was sensative to fuel pressure. I had to run a pressure regulator to control this.
 
Back
Top Bottom