calling pinhead and idave....electrical updates

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 11, 2004
Threads
182
Messages
2,250
Location
Kansas!
hey fellas
this wiring issue is about to wear me out!....went out today and bought and amp meter and installed it...reading 0 while engine is running...turn on headlights needle moves ever so slightly to the + side of the guage...same with headlights and e flashers...first question...this is what i read to be a normal reading...correct?....next question...when i un wire nutted the two wires that now reside on the back of the amp meter the parasitic drain i have been chasing stopped....what does this indicate?..and and all help and comments welcome...i have determined that my voltage regulator is not in use....and yes i am still chasing the battery drain....
thanks for all the help...

osagecruiser
 
Basically ALL your draw from the battery goes through that wire to the ammeter, except for the starter motor. So, of course the drain goes away when you disconnect it. Did you pull all of the fuses while the ammeter is hooked up?

From the ammeter there are two branches. One goes to the fuse box and the ignition switch. The other goes to the Alternator.

I would now:

1) pull all the fuses

2) Disconnect the BR wire (or whatever color it is) to the AM terminal at the ignition switch.

3) Disconnect the WL (or whatever color) at the B terminal at the Alternator.

4) Hook up both ammeter wires.

5) Hook up battery.

6) Now, do you still have your drain?
 
p.s. This is fun!
 
thanks i dave....i am gonna print this and head for the driveway to try it out....i got to be at the baseball field in an hour so if i don't report right back i will later on or tomorrow...i reallly am greatful for your help!

osagecruiser
 
BTW, on the ammeter, a deflection to the (+) side means you are charging your battery with the alternator. Headlights and radios will pull it to the (-) side.

If its the other way around, you've got your ammeter wires backwards.
 
I don't have much to add to what Dave already said. Since the drain went away when you disconnected the amp meter, you can conclude that the wire from the battery to the meter isn't shorted. Normally, the meter should deflect slightly to the left (-) when you turn the lights on. Does it deflect left when you turn on the lights with the engine off? If so, it is reading correctly, If it deflects right (+) you have the wires flipped.

As for the drain, next hook up one of the two wires at a time that go to the other side (-) of the amp meter like Dave said. One is the Alternator B+ wire and the other goes to the igntion switch and then the fuse block. If it is in the ignition side, then disconnect the wires to the fuse block.

If I had to guess, I would bet is is the ignition switch, because it is subject to wear.
 
osagecruiser said:
i dave...fyi..i have not pulled all the fuses...yet...which screw on the ignition is the am?...there are 4 screws on that dude...thanks for the help

osagecruiser

It would be the screw with the "B" for "battery" mark on the brown plastic closest to it.
 
IDave said:
p.s. This is fun!

Only from you would I expect that comment;p

When I work on computers at work and make comments like that, my co-workers give me that stare of "You've got to be nuts";)

Well, you, Pinhead, and Poser are the land cruiser geeks here;p We all learn a great deal from you. Thanks for your patience, increadible knowledge, and willingness to help! :cheers: :beer:
 
That's kind of you to say, but I'm hardly in the class of Poser and Pin_Head.

Working out wiring is like doing jigsaw puzzles.
 
idave...

i just removed the ignition switch from the dash...five wires to it...maybe pinheads thoughts on the ignition are on the money...there are 4 copper posts with screws for wire connection.....they are lettered...B...ST...IG....ACC....i think...they are kinda hard to read.....what wires to what posts are correct....three of the five wires were connected to the ignition post...one to the battery post and one to the starter post ....no wires to the ACC post...where do each of the wires that should be there go to?....i thought if i made sure this was correct...i had my doubts thats why i removed it ...then i would back track though the items you listed above...thanks cant wait to get this beast laid to rest...the nice part is i am cleaning up this wiring mess and then will have an organized system....easy to work on..HA!

osagecruiser
 
In the factory configuration, there would be three wires only.

One to IG, (BY) to the Coil (with a branch to the switched side of the fuse box).

One to B, (BR) which is the wire that is the branch off of the WL wire between the unswitched side of the fuse box and the ammeter.

One to ST, (BW) which is the wire that goes to the starter solenoid.

The stock setup had no ACC wired in, although all of the ignition switches have a terminal marked that way.

WHO KNOWS what the other two wires you have are? :D

Perhaps one of the other wires off the IG goes to the fuse box, rather than branching later the way it does in the stock configuration. It would be for the meters, turn, and heater fuses.
 
idave

i did some tracing...i have a white wire that goes from the IG post to the alternator...smaller wire....from the ST post i have a black wire/white stripe that goes to one of the small post on the starter...from the IG post there is a black wire/yellow stripe that goes to the fuse block and then on to one of the small post on the starter...also from the ig post there is a green wire that goes to the distributor/electronic one i believe...i have to trace the one wire left that comes off the B post.......i am growing weary but i will...continue on..tell me what you think of the wiring configuration listed above...thanks

osagecruiser
 
Well, the ST terminal BW wire is right.

The BY wire from the IG terminal to the fuse box is right, also. But the BY wire should go to the coil positive terminal from there, not the starter in the stock configuration.

In my later truck, the mini, the BY wire from the IG terminal goes to the IG terminal on the internally regulated alternator.

In the later truck, the BR ignition wire goes to the coil positive terminal.

Do you have an internally regulated alternator? I couldn't remember.

Anyway, you need this setup, from the ignition switch:

ST terminal--BW wire to the starter motor solenoid.

IG terminal--fuse box, coil, VR or internally regulated alternator, possibly ignitor(only if you have an ignitor/electronic distributor).


And, of course, the B terminal wire goes to the Battery post on the starter, or directly to the Battery, with an aside to the fuse box unswitched fuses.

I've looked through a bunch of different toyota setups over a 20 year span, and none of them are set up like yours. :D ;)
 
idave
yes i have an internally regulated alternator...i verified that yesterday down at the local autoparts store....the configuration you describe above applies to a chevy 283 engine?...i just want to be sure you did not forget we were talking a hybrid here...i am gonna do some more investigationg this evening...may try to reconfigure to the description above...let me know...

osagecruiser
 
On all my starters it's a spade connector to the passenger side of the main terminal. (except the very earliest one I have, where it's a screw in that position). :D

I think the basics are the same for chevies and toyotas, as well as other vehicles, as far as the ignition switch. Think about it: you want the starter motor running when the key is in the STart position. Everything else stays on when you have the key at the IGnition position, including the IGnition, coil, alternator, and switched electrical items.
 
thanks idave...the last post helps me make sense of some of this...this is gonna sound stupid...but where exactly is the coil?..boy i am really showing my lack of knowledge now..i am thinking i am real close to getting this right...i really appreciate the help...is there a chance i do not have a seperate coil..but it is part of the distributor?...or what i call a distributor...all the spark plug wires go there...

osagecruiser
 
That distributor has a fat wire in the middle that doesn't go to a spark plug. That one connects to the coil. There may be another little wire that connects the side of the distributor to a different terminal on the coil. Correct?
 
Back
Top Bottom