Bumper Departure Angle - Kaymar

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 13, 2006
Threads
28
Messages
492
Location
Abbotsford, British Columbia, Canada
Not looking for a completely scientific answer here but...

I've searched the 80 forum without much luck in finding the answer to my specific question, how much does the Kaymar rear bumper stick out, compared to say, the stock bumper and/or anyone else's aftermarket bumper?

I know that lots of Cruiserheads complain of bumper drag with the Kaymar on departure and it sounds like it is simply attributed to the receiver sitting lower than other designs. This I could put up with, but I wouldn't want to be dragging the thing all over the place. From what I gather from other threads the Kaymar mounts flush up to the rear cross member, so I wouldn't think that it can sit much further out than stock, or anyone else's bumper for that matter.

I like the Slee rear bumper for its nicer appearance, tidier shape, and clearance at the quarters (it sounds like its stronger here too), but I need to be able to tow (utility trailer) and I like the idea of the second swing-out on the Kaymar for the gas can (storing gas cans on the roof rack doesn't seem like a good idea to me, weight wise or for accessibility, nor would I want to go through the hassle of a sub tank install).

The only other bumper that I ran across is the 4Plus that M-A-F used to sell, but it looks like it's long gone from the market (never mind having to send your truck off for 6 weeks to get one fitted, what the hell was up with that?).

I'm planning on getting in touch with Slee shortly to purchase his 4" lift, and I'll be tucking 315's into the wheel wells so the departure angle may not be an issue for me anyway, especially since I will be doing mostly expeditionary trips with my LX450.

I would just like to know how much overhang I'll be building onto the back of the truck by going with the Kaymar. Anyone out there have approximate dimensions? It's tough to tell from pictures.

Thanks all...
 
check out lukes (4X4 labs) bumper. its an excellent design, available double swingouts, built in hitch (although probably not rated for towing...how heavy a trailer?) and excellent clearance. only one drawback...it requires cutting the rear cross member, so its a pretty permanent fixture should you chose to go that route.

theres a member here in chilliwack (Cruisin' is his handle) working on a rear setup...should be interesting to see what he comes up with. hes done some great fabwork so far. check the 'bumpers in BC' thread here in the 80s section.
 
...it requires cutting the rear cross member, so its a pretty permanent fixture should you chose to go that route.

I ruled out the 4X4 Labs for that reason, I'm not going to mod my truck to fit a bumper... :rolleyes:

Interesting to hear about Cruisin' though, but unless he has something to go off the shelf soon I'll go with Kaymar if the overhang isn't too bad.
 
Last edited:
Kaymar definitely sticks out further on the corners than a Slee, and also further down on the receiver hitch. Is that a big deal? Your call, it's not to me.. most of the "big" obstacles while wheeling every bumper drags... I've had mine all over Moab, Colorado, and run the Rubicon.. and it's still going strong with pretty minimal damage. Heck look at the 4WDTO rig, those guys beat the hell out of theirs...

It's not as tough as a Slee, not as good as departure angle as a Slee, but I like the lights, the looks, and I like the integrated hitch, so it's the right bumper for me. maybe you too!
 
My Kaymar does stick out more on the quarters than other bumpers like Hanna, Slee, Luke, etc. While Slee's bumper is not rated for towing(cost, etc. to do so) it certainly 'look's as stout as my Kaymar for that purpose.

Most/all my driving is more expedition style as well. I've encountered more drag out on the quarters where the Kaymar really looks 'fat' compared to the others than at the tow hitch portion. At least that's where all the scuff marks are! :D IMHO, the Kaymar does stick out further than a stock bumper, not much, but I think it does. It probaby looks worse than it really is because of the side quarters that don't angle up like other aftermarket bumpers.

While I don't know the attachment points for the others, the Kaymar uses the same 3 bolt holes under the frame that an OEM hitch does. It also uses 2 bolts on each side into the side of the frame in addition to 2 more bolts into the treaded pintle hook attachment point on the rear crossmember. It's not going anywhere.

Somebody else can chime in on Slee's to compare.

If you like the double swing out, need tow and are unwilling to cut your rear crossmember, sounds like your choice is one - Kaymar. Hanna has a double swing out, but I don't think Ken has ever modded his sweet bumper to tow. Don't know if you carry a hi-lift and if so where you secure it now, but the Kaymar solution mounting it in a perpendicular position on the outside of the tire with an add on attachment sucks. I'd much prefer it behind the tire. One person on this board has modded his Kaymar for that but it's a tight squeeze!

Don't know if that helps or not, but I've been happy with my choice of the Kaymar because of my need to tow. Slee hadn't yet come out with a production tow package at the time I purchased my Kaymar or I'd have had a tougher choice.
 
The Kaymar drags. Mine was fitted in 97. The new ones are a little better in the corners I think. I've hit mine all over the place with 33 tires and 2.5" ome springs. The plus side is it can definitely take it. The recovery loops get bent though and have to be periodically straightened to use the hi-lift adaptor sleeve.

For me the low corners are more of an issue than the hitch mount.
 
measured it for you.

departure angle: 30 deg at bottom of the receiver.
 
........ Heck look at the 4WDTO rig, those guys beat the hell out of theirs....


X2. - You're talking about Dave's green '95, not the orange & white project '94, right?
Their project '94 has a TJM rear bumper.

Back to the' green '95,
- that's got the Kaymar that he added the hoops on the wings for protection before he ran the Rubicon. You're right, he thrashes that thing pretty hard!
Search on keyword Kaymar in "search titles only" for 3 pages of threads about Kaymar bumpers.
 
Last edited:
measured it for you.

departure angle: 30 deg at bottom of the receiver.

Wow, thanks, I wasn't expecting anyone to go out and measure the departure angle. I guess that's variable really, it depends on lift, tire size etc., but it's good to know.

What is constant is the actual overhang say from the tailgate to the edge of the bumper. To me it looks to end at the same place as the stock bumper, so I don't think it would be any worse than than the exit angle with a stock bumper.

I think that the Kaymar has the appearance of being longer than most due to the length and width of the panel from behind the wheel to the back of the bumper, others angle under the truck at that point, which must help prevent hang-up... I wonder why Kaymar didn't do this.
 
It's not as tough as a Slee, not as good as departure angle as a Slee, but I like the lights, the looks, and I like the integrated hitch, so it's the right bumper for me. maybe you too!

I totally agree, to me it's not really a question of quality, but of practicality, at the end of the day I know there aren't many options if you want the degree of flexibility that dual swing outs offer, and the Kaymar definitely has function nailed especially with it's burly tow capacity.

I've been on long trips, as we all have I'm sure, where I'm in the middle of the desert running on fumes, wondering where the next gas station is because what appeared to be a significant town on a map turned out to be nothing. Poor planning on my part perhaps but, to me an extra few gallons of gas is handy to have at that point.

Regardless, I know that there will be technical trails here in B.C. (rocky and steep) that I want to run and at some point I may be cursing the boxy looking Kaymar. I asked a guy here locally about the Kaymar and the first thing out of his mouth was a comment on how much overhang it adds to the truck.

I've read that some have sold their bumpers after deciding that they can't live with the overhang. I doubt that will be the case with me but it's always nice to get it right the first time when you're spending the better part of $2500 with taxes and freight on a bumper!
 
I have dragged the corners of the Kaymar many times bearing a lot of vehicle weight and it has nothing but some scratches underneath. It's very strong and scratching the underside of the corners doesn't bother me at all. By constrast, I have very few scratched marks on the tow hitch.

The dual swingouts are great and can bear a lot of weight. I have modded mine to carry all sorts of stuff like gas cans, tire chains, propane, and bikes all while being able to swing that stuff away and easily access the rear hatch. Another plus is that the rear bumper makes a great step if you need it.
 
I have dragged the corners of the Kaymar many times bearing a lot of vehicle weight and it has nothing but some scratches underneath. It's very strong and scratching the underside of the corners doesn't bother me at all. By constrast, I have very few scratched marks on the tow hitch.

The dual swingouts are great and can bear a lot of weight. I have modded mine to carry all sorts of stuff like gas cans, tire chains, propane, and bikes all while being able to swing that stuff away and easily access the rear hatch. Another plus is that the rear bumper makes a great step if you need it.

I thought I saw a kitchen sink on one of those swing out's too! :lol::lol:
:cheers:
 
measured it for you.

departure angle: 30 deg at bottom of the receiver.

My 4x4 Labs is ~42 degrees, but may have slightly more tire/lift?:hillbilly:

...
Regardless, I know that there will be technical trails here in B.C. (rocky and steep) that I want to run and at some point I may be cursing the boxy looking Kaymar. I asked a guy here locally about the Kaymar and the first thing out of his mouth was a comment on how much overhang it adds to the truck.
...

Check out the 4x4 Labs bumper. In my experience by far the best design if you plan on wheeling hard enough to get ground contact. All of the square lower edge bumpers tend to catch on uneven ground, transferring big loads to the bumper and/or hanging you up, especially when backing up. The 4x4 Labs also has modular swing arms, so you can change/choose what works best.

Bumping around in some rocks, the side "wing" of my Kaymar put a nice line in the rear qtr panel.

X2, have seen this a couple of times. The wheelers that I know who have them wouldn't buy a Kaymar again today.
 
My 4x4 Labs is ~42 degrees, but may have slightly more tire/lift?:hillbilly:



Check out the 4x4 Labs bumper. In my experience by far the best design if you plan on wheeling hard enough to get ground contact. All of the square lower edge bumpers tend to catch on uneven ground, transferring big loads to the bumper and/or hanging you up, especially when backing up. The 4x4 Labs also has modular swing arms, so you can change/choose what works best.



X2, have seen this a couple of times. The wheelers that I know who have them wouldn't buy a Kaymar again today.
The Op already said he doesn't want to cut up his rig to put on a bumper (post#3) and being a satisfied Kaymar owner myself and knowing it's limitations, I can appreciate the 4x4 Labs bumper. Yes, it makes the 80 slightly more trail worthy, but I think the OP is looking for a bumper to install without a cutting torch & welder, which is what's needed for the 4x4 Labs install. That is what is great about this forum - you can get feed back on a mod before you do it. A careful Mudder should be able to get, pretty much, just what he wants - plus have the help he needs if any questions pop up.

I won't argue that the 4x4 Labs has got a better departure angle and the corners are tucked in and better protected. I will argue, though, that where the 4x4 Labs is superior is terrain that most, not all, 80 owners avoid. Yes, most of us like to test our rigs from time to time, but there's a certain element among us, that is constantly doing the extreme - crossing up the axles, ascending and dropping off ledges, banging bumpers and skidplates to their limits. These are the owners that need the 4x4 Labs rear bumpers and shortbus front bumpers, 3 link axle setups, 37" tires and full length skidplates. A built 80 is an awesome rig, but some of us don't need or want to modify that much. It's tempting, sometimes, and nice to know that these mods are available and entertaining reading threads like "Wild Wheeling Pics". I like the 80's reliability and have quite a bit invested in it (time & $) and have trouble taking unnecessary chances so I'm pretty conservative off road. I guess since I have an ARB and a Kaymar that's a good thing.:rolleyes:
 
Last edited:
The Op already said he doesn't want to cut up his rig to put on a bumper (post#3) and being a satisfied Kaymar owner myself and knowing it's limitations, I can appreciate the 4x4 Labs bumper. Yes, it makes the 80 slightly more trail worthy, but I think the OP is looking for a bumper to install without a cutting torch & welder, which is what's needed for the 4x4 Labs install.

Sorry I missed post #3. :whoops:

If an assembled 4x4 Labs bumper is bought, there is no need for a welder or cutting torch, just a saw to remove the rear cross member. A few years ago when I installed mine, the rig was still worth good $$$ (~60K mi, ’96 LX, very clean) so it took some soul searching to take the saw to it. I cut it clean, so I could easily weld it back on, now it’s kind of silly, because the rig has about fully deprecated, pretty much worthless as far as resale goes.

That is what is great about this forum - you can get feed back on a mod before you do it. A careful Mudder should be able to get, pretty much, just what he wants - plus have the help he needs if any questions pop up. ...

I agree that this is a great forum, but have seen it cost lots of members lots of unnecessary $$$. My story; bought the rig to enjoy the backcountry, didn’t really understand it’s capability or where/how I would want to wheel it. Did plenty of “Mud research” at the time the “Mud setup” was 2” OME lift and 285 tires, anything more requires way to many mods. It wasn’t my first wheeler and have always been a firm believer in the saying; bigger tires make all obstacles smaller, so went with 295’s, 2” lift and an ARB bumper.

Hooked up with a local club and noticed that most of the rigs were taller/bigger tires than mine. The first trail run confirmed my fears, a slightly taller lift and bigger tires work much better in our local terrain. My brother got one a few months latter and put a J lift and 315’s on, with much better results and I joined the trail chorus that said; when these little tires wear out I’m getting bigger.

When I read: “I wouldn't want to be dragging the thing all over the place. I know that there will be technical trails here in B.C. (rocky and steep) that I want to run and at some point I may be cursing the boxy looking Kaymar. I asked a guy here locally about the Kaymar and the first thing out of his mouth was a comment on how much overhang it adds to the truck.” I think of all of the locals who have bought rig mods twice. My recommendation is to research everywhere, but put the most consideration towards the opinion of locals that have run and/or you will be running local trails with.

It's impossible to predict how “bitten” with the wheeling bug anyone will become. A well setup ‘80 is easily capable of 4+ rated (out of 5) trails. I’m also conservative with the rig on the trail, have to be, mine is pretty much stock with bumpers, lift and tires. Seat time in the rig changes outlook, stuff that is easy, no big deal now, I would have thought of as crazy, destructive, silly places to take a station wagon 6 years ago. :hillbilly:
 
Look at Slee and Iron pig offroad. As someone who used to weld hitches and such for big trucks at work, the weak link in towing with an 80 is not the unrated hitch on a Slee or IPOR bumper, it's the 80 itself. I've built hitches for 10,000 lb trailers attached to Kenworth service trucks that looked just the same as a Slee. The difference is paying a few bucks to have a structural engineer to rate the load of the hitch, and then paying for the welding quality control. I can understand why a small fab guy would want to avoid that cost. It's all about not getting sued.
 
I purchased the Slee bumper and sold it at a loss before I even installed it because I decided I wanted the tow capability of the Kaymar. My biggest complaint about the Kaymar is the fact that they do not finish the Tire Carrier or Jerry Can Holder in the same way they do the bumper. My Jerry Can Holder rusted immediately, MAF replaced it, but the new one did the exact same thing. It had t be sanded and painted to stop the rust from spreading out of control. Other than that, it seems like a good bumper. I have not wheeled it yet but I can tell you it bottomed out slightly on a rock when we were goofing around in the builder's backyard.
 
I purchased the Slee bumper and sold it at a loss before I even installed it because I decided I wanted the tow capability of the Kaymar. My biggest complaint about the Kaymar is the fact that they do not finish the Tire Carrier or Jerry Can Holder in the same way they do the bumper. My Jerry Can Holder rusted immediately, MAF replaced it, but the new one did the exact same thing. It had t be sanded and painted to stop the rust from spreading out of control. Other than that, it seems like a good bumper. I have not wheeled it yet but I can tell you it bottomed out slightly on a rock when we were goofing around in the builder's backyard.

Hmmm...wonder what MAF does with those returns? I'd love to get my hands on a DS jerry can holder cheap. I want to hack the single carrier and have a double/triple carrier fabed up.
 
Back
Top Bottom