Break-in Methods

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 12, 2005
Threads
287
Messages
3,081
Location
Littleton, Colorado
Hey there, finnaly figured out the fuel delivery, so now the fuel pump suckin gas and she purrs like a cat ;p

just wondering if theres anycertain breakin methods? i know not reving it high, driving at high speeds etc. but anything that we should do before the first drive?


thanks guys ... and girls ;)
 
If the motor got a new cam and lifters then run it at 2000 rpm for 20 minutes to break in the cam and lifters. Then shut it down, drain oil, change oil filter, refill with new oil. Refire, check timing, warm to operating temps, shut down and readjust the valves. Then drive gently for 500 miles. Gently means no full throttle accelleration or winding out to redline. Vary the rpms while cruising. After 500 miles drive it normally. At 1000 miles retorque the cylinder head, readjust the valves and change the oil/oil filter again. Then normal maintenance schedule.

I've done a few motors this way with no problems thousands of miles later. It's also what the motor shop I used to work for described to customers when they picked up fresh motors.

Enjoy!
Nick
 
Yes, because the two surfaces still need to "mate", even though the cam is not new, it is new to the lifters.

GL

Ed
 
petescoffee said:
Ditto above on the cam shaft and lifters. I was told by an engine shop to use a non detergent oil for break in.
Retorque head after warm up. Check head torque again after 500 or 1000 miles.

Ya, non detergent for 500-600 miles and then switch to multi viscosity. It'll help seat the rings. Retroque all the cork gaskets on a regular basis for the fisrt couple 1000 miles. You should also change the oil and filter after your cam break in, or after initial runs if your not replacing cam and lifters.
 
Thanks Flyinglow and Pete, did not know about the non-detergent. I had been warned that the first oil change would look like a milkshake due to all the assembly lube.
Unless I can just unbolt the headers and not have to cut the exhaust pipe, the neighbors should be well aware of the lifter break-in date. Last time I ran it with open headers I felt like Rapid Roy the Stock Car Boy.;)

Ed
 
ok well i got my motor in tonight and i did change the cam and lift, so let it run about 20 mins at 2000 rpm, change oil filter and oil then be eazy?
 
Proper way to break in a new cam and lifters.
With the engine at 1500 rpm, gradually bring the speed up to 2000 rpm and then slowly bring it back down to 1500 rpm. DO this for about 20 minutes to properly break in the cam and lifters.
Secret is to not let an engine idle for the first 20 minutes of its life.
This is why it is critical to getting the timing dialed in a close as possible, the engine oil system primed, and the air fuel mixture close. This way when you first fire it up you can do the break in and not screw around trying to get things adjusted so it will run.
 
Oh ya, Ranger is right, PRIME THE OIL PUMP. Go through the distributer hole with a dizzy shaft or a screwdriver that you put in a drill to turn the oil pump. Go until you get oil pressure.

Ya change the oil after cam break in so anything left in there (lint, dust etc) is cleaned out. I think you could get away with running regular oil for the cam run in and then run non detergent for ring seating (500-600 miles). Check the price, I'd go with whats cheaper.

For the first 500-600 miles, highway driving is best, changing power regularly. A little road trip maybe?
 
Rock_Hugger said:
people have differnt theorys on break ins, I am usally pretty easy on new motors but found this link, interesting .

Break in info


I didn't read alot in the link as I can't stand the way the content is displayed. Anyway is this the theory to hammer the hell out of the engine with heavy rpms?

A friend of mine uses that technique in his 911's, cummins and duramax's. He swears by it but has never sent me the link.. he couldn't hook a wireless router though so I don't hold it against him that he never sent the link ;0)

I can't remember but I thought it had to do with newer ring composition...

anyway... rambling here.
 
My understanding is back in the day nondetergent oil was the only oil available. Engines did not last as long as do when normal oil is used. It does help to run nondetergent oil when breaking it in and then go to a normal oil after your first oil change it And yes stay away from synthetic oil until the engine has been broken in.

zebrabeefj40 said:
Not sure if the non-detergent thing is that big a deal. Never worried about other than to not use synthetic for break-in. Can't hurt either way IMHO detergent or non.

Nick
 
The non detergent just helps the rings seat a little better and faster. It actually holds the metal particles in suspension on the cylinder walls to seat (wear) the rings.
 
Rock_Hugger said:
people have differnt theorys on break ins, I am usally pretty easy on new motors but found this link, interesting .

Break in info

Guy I used to drag race with employed this method. Not as scientific though. As soon as the motor fired, it was up and down the street once at part throttle, then the next one wide open.

He swore by it, and never had a problem.
 
Back
Top Bottom