Brake question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 5, 2017
Threads
3
Messages
11
Location
Dayton, OH
i recently bought a 91 that needed a little TLC, and by little I mean a new steering box, driver floor and the brakes bled. Wellll I welded in some sheet steel, shelled out $400 for a steering box and replaced front calipers, master cylinder and pads and shoes all around. But the kicker is I have no brake pressure once the car started, while it's not running the pedals rock hard. Oh and one of the previous owners took the LSPV off. So does anyone have any ideas on what to do?
 
Pedal should be hard if off. Sounds to me to be the master cylinder if you have no pressure or, brakes are not bled properly. I used a homemade pressure pot on mine today to bleed the brakes. Took me about 15 to 20 minutes, by my self, and the brakes are FIRM! So

1. Try bleeding the brakes, and the lspv
2. If the brakes still go to the floor it is the master cylinder. You may have damaged it during the install or it was bad out of the box. I have personally seen both...
 
Pedal should be hard if off. Sounds to me to be the master cylinder if you have no pressure or, brakes are not bled properly. I used a homemade pressure pot on mine today to bleed the brakes. Took me about 15 to 20 minutes, by my self, and the brakes are FIRM! So

1. Try bleeding the brakes, and the lspv
2. If the brakes still go to the floor it is the master cylinder. You may have damaged it during the install or it was bad out of the box. I have personally seen both...
My concern is that one of the previous owners took off the lspv, and I'm not sure if the system would run correctly without one
 
Brake check.webp
 
Gonna second air in the system. Bleed LSPV, then RR, LR, FR, FL. Have a helper.
 
LSPV should not be the first one to bleed.

That's what I used to think and the FSM says too, but others state/swear to do it first. It can be hard to get air out of the LSPV. I've done it both ways with success. So ????, I dunno

Soo it sounds like I need to put a lspv back into the system?

I never understood why people do this. Choice is yours but it was done properly, it should not be an issue.
 
Well, when I get back in town Monday I'm going to bleed it all again and I let you guys know how it goes. Thanks for all the advice!
 
There are LOTS of folks here that have deleted the LSPV. HOWEVER, You may want to read up on it and make sure the PO did it CORRECTLY. There are a few fittings that you have to re-use and there are some line re-routing that goes on.

You do NOT have to have the LSPV.

Did the 91 have ABS?
 
I deleted the LSPV, easy to do and am happy with the results. I rigged up a tool like shocktower did using a garden sprayer to bleed the brakes. I have tried two different vacuum tools and neither was effective. Two man works but is time-consuming. Pressurising the system worked by far easier and more efficiently than either.

There is a valid concern about the hose coming off of the brake reservoir and spraying brake fluid everywhere. To address this use about 8 feet of hose to attach to the reservoir and then clamp the lid on with a hose clamp.
 
There is info about deleting the lsvp in some threads. One even with pics of brake line routing. As already mentioned,
read up and verify it's correct. Of its still there make a decision of you want to keep it. I would remove it then enjoy it's absence! Thats nust my opinion. There are one million threads about brake bleeding. Skip right to the all advice given above. If you have abs there will be a football sized actuator with many brake lines mounted driver side wheel well just forward of the master. Can't miss it if it's there. If you do have abs then it can be a little more involved to bleed the air out if it. Oh, and whoever said to bleed the master, follow that persons advice too.
Good Luck
 
Back
Top Bottom