Brake issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 28, 2012
Threads
63
Messages
247
Location
Missoula MT
Hi all I am having some brake issues. My brakes seem to suck lately. They are the worst when I first take off driving. If any down hill I almost cant stop. The pedal goes down and kind of gets hard. It doesn't go to the floor. They do get a little better after driving a while. I do have one of the cruisers with drum rears in it. I did also just get bigger tires 285/75r16. But don't think that that would affect the braking that much. Also did lift 2.5" and haven't adjusted the lspv or what ever that thing is called. Any Ideas?
Thanks
 
I would start with bleeding the system and flushing the brake liquid. Also check for pads/shoes wear, even disks too. Maybe they need to be replaced.
Boost leak too?
 
Make sure your lspv has been adjusted for the lift.
 
Cool will try flushing and bleeding. I did look at the fluid this morning and its a little green. I will look into adjusting the lspv. Is the booster the big round thing on the fire wall?
 
The brakes on my 80 suck as well. I've rebuilt calipers, replaced lines, flushed, bled, etc... all to no improvement. Panic stops are scary and don't result in good stopping. I don't have a lift. They sucked with stock tires, they are bad with 285's also.

I read here people saying that they are fine with 35" tires, stops great, etc... but I can't replicate it with my rig. I'm thinking that there is a loss of line pressure somewhere in the system but no way to know for sure, so I ordered a brake pressure gauge kit. It attaches in place of a caliper and tells you how much PSI the system is developing (up to 3000). My main theory is that the ABS system is leaking internally and bleeding pressure off, but want to actually diagnose it before I go about trying to fix it by throwing any more parts at it. Once I get the gauge, if I find it of any use at all or learn something I'll report back here. I can also hook it up directly to the master cylinder so I can see the difference between what the master cylinder is producing vs. what I find at the wheel.
 
grab some brake cleaner and start cleaning. pump your brakes and look for leaks. you may need to change your rubber lines. when I had mine apart on my 96 all the lines are starting to crack so I will be calling slee for a fresh set.
 
I was looking at the procedure for bleeding brakes in the faq. I have a few questions. First off should the truck be running while pumping the brake pedal? And next question is when to bleed the lspv. In the faq it says to do it after the back 2 brakes. But when I search I see a lot of people saying to do the lspv last. What is the right order?
Thanks
 
My brakes sucked on panic stops until I adjusted the lspv. Now the abs will kick in on dry pavement. Had to bleed the brakes a few times to get all the air out. The last little piece was to get the abs to activate on a dirt road and then bleed the brakes again.
 
Start with the wheel that is the farthest away from the brake pump. 1) Rear PS 2) lspv 3) rear DS 4)front PS 5) front DS

It's better done with two people. I like to have the engine running because the gases smell so good.
 
I ended up lowering the lspv. Then I bleed all the brake lines until the fluid became clear. The difference is amazing. The lspv came down just over 1/4 inch. It was very difficult to move. the bolts came off no problem but the lspv was stuck to the bracket. I may have moved the lspv down a little far but my brakes are working better than they ever have. Thanks for all the help mud.
 
I ended up lowering the lspv. Then I bleed all the brake lines until the fluid became clear. The difference is amazing. The lspv came down just over 1/4 inch. It was very difficult to move. the bolts came off no problem but the lspv was stuck to the bracket. I may have moved the lspv down a little far but my brakes are working better than they ever have. Thanks for all the help mud.


Did you adjust at both ends? Off the body and axle?
 
I adjusted the valve and then I felt all the brakes working correctly and then tried to squeeze just a little more by adjusting the axle end.
 
I chickened out seeing those metal lines, so I only raised the rear end. I'll probably get on with the front end of it this weekend. Maybe 1/4" lower.
 
Do it! You won't regret it! The lines bend pretty easy. You would have to work really hard to damage them
 
If the pedal doesnt go to the floor, but firms up, check the booster. If it is the original booster, get a new or rebuilt one. The brakes probably because there is no booster input.
 
Back
Top Bottom