BJ74 Parting out

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

HFXcruiser said:
I'm looking for the inner fenders complete.

My upper and lower fenders are rebuildable but I need the inners .

I'd consider the cowl and rad mount as well as the fan shroud.

I'll post you a pic of my project tonight.

This is a winter project and I'm not even close to needing these

parts yet but if and when they are available i want first crack at

them.

Dave Hutchings
Click to expand...

Sorry, entire front clip is already tentatively sold
If something falls through I will let you know
 
Yes, $50 plus shipping for the RHD wiper arms.
Have LHD J7 wiper arms too
 
Got a couple of sets of LHD wiper arms.
1 set from LHD BJ70 $50 plus postage
1 set from LHD HZJ75 (same stud size, much beefier arms, clean rust free incl blades etc) $120 plus postage
 
Ya.. that thing should still be in there, the wheel is still in place.
 
I'm looking for an exhaust manifold for the 13b-t. Mine is cracked I - I know you mention the engine and tranny aren't available, don't know if the manifold was tied up to?

Tanner

edit: also looking for complete suspension set up - springs, bushings, shackles, shocks etc -what kind of condition are they in? what brand?
and also looking for the vsv vacuum valve thing on the firewall
 
Last edited:
jake2far said:
Hey,
Is the rear diff complete still for sale?
Thanks
:bounce2:
Jim
Click to expand...

Maybe. I have a deal pending on the axle set, so I have to see how that
plays out first.
 
torqueluvr said:
I'm looking for an exhaust manifold for the 13b-t. Mine is cracked I - I know you mention the engine and tranny aren't available, don't know if the manifold was tied up to?

Tanner

edit: also looking for complete suspension set up - springs, bushings, shackles, shocks etc -what kind of condition are they in? what brand?
and also looking for the vsv vacuum valve thing on the firewall
Click to expand...

The manifold is staying on the engine. Check with Dave at japan4x4.com for a new one out of Japan.

The suspension appears to be stock leaf packs with extended shackles, nylon bushings. It's in good shape and has enough lift to fit 33s. Has recently replaced stock Toyota shocks. $400 for all of it. Have a lot of work to do yet before I can em out though.

24v Vacuum switching valve set for Tcase control is available $100
 
WILD FX said:
Wicked ...So how much ? paypal? shipped to New West BC ?
To make it easy I will take all the guts needed ..
Thanks for the quick and kind response !

EDIT
cig lighter as well
Click to expand...


Nick, you got pm.

Cig lighter is sold.

Sheldon
 
Sounds great. I'm looking for something that will last me 4-5 years, and I'd be using the Cruiser as a city/road vehicle. Do you think that setup would do it? 5 years down the road I won't be a student anymore and hopefully there will be more cashflow.:)

Here is a pic of my setup right now. As you can tell the springs are pooched. My front end is bottoming out all the time.

DSC_0438.jpg picture by Tannerbp - Photobucket

Put me down for the suspension assembly. No rush on it either. I'm making a trip out to Coquitlam (in-laws) in February and I could pick it up then.

I am extremely appreciative of this offer and if there is anything I can do to make it easier, let me know.

Eternally grateful (if we go through with it)

Tanner
 
Ya, those look pretty flat.
I took some measurements, 6.5" front, 7.5" rear, I've pulled the bump stops already so the measurements are distance between the top of the axle tube to the bottom of frame rail where the bump stops mount.

I'll pencil you in for em. Feb should work. If your plans change let me know.

Sheldon
 
You got PM back.
 
You must log in or register to reply here.

Share this page

Back
Top Bottom