Birfield Replacement

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 17, 2009
Threads
60
Messages
244
Location
South Central NH
Hi guys I am starting to hear some clicking in my wife's 80 from the birfield. When I rebuilt the knuckles last year I swapped the birfs side to side to try to get some more life out of them but as luck would have it, it only bought me a year. I'm not complaining as the rig now has 240K and going strong. Through my reading because this is my wife's DD longs are not suggested. I am looking at the nitro's. It seems that people are doing the birfs and the axle. In effort to save money is it fine to just do the birf. After all that is what is clicking right? I don't mind spending the money for the birf/axle set if is necessary but I can't seem to find it necessary to do the axle too. My wife DD's this rig and I have a 40 for off roading I don't think this rig will see any significant off roading. What are your opinions?
 
Terrain tamer also has birfs. As long as there are no grooves in the axel where the seal rides I would do just birfs. Mine have grooves and I adjusted where I mount my seal but next front axel job I will likely replace one birf and both axels. Will go with nitro or terrain tamer.
 
My birfs were shot (stripped drive flanges) and I bought the Terrain Tamers from @beno and was very satisfied with them.
 
@beno (Onur) is the BIRFboy :clap::clap::clap:

Terrain Tamer p/n 43405-60070 for the ABS version (FZJ80) at $169 suggested retail, including clip and lube.

Onur and our other resellers can also supply Terrain Tamer drive flanges and spindles to suit. Also available for earlier FJ80.

And while you are in there, the Terrain Tamer knuckle rebuild kit with Koyo trunnion and wheel bearings p/n SH5WB is available from Onur, et al, at $205 suggested retail.

Another cool tool for 80 Series owners is Joey Romero's reference chart with an exploded view of your front axle, including knuckles. Check out his Wits' End Online Store here 80 Series Front Axle Reference Poster- 18"x27" or PM him at @NLXTACY

CV Joint.webp
upload_2017-1-1_8-0-30.webp
 
Last edited:
And for your viewing pleasure, a pretty good video on 80 Series CV joint maintenance.

The star of that show is Alan Gray, Terrain Tamer's long-time resident mechanical guru. Alan worked on the very first Land Cruiser to arrive in Australia some 60 years ago. At 84 years of age, Alan still shows up at Terrain Tamer HQ in suburban Melbourne and their products are imbued with his experience and spirit.....humor as well. Check out an article on Alan here No Cookies | The Weekly Times

 
Last edited:
Alan is my hero!
 
When I switched them from side to side I filled them as recommended from guys here on mud but I could try to fill em through the fill plug. Can't hurt. Thanks for all the comments & suggestions. I will check for grooves when I tear them down for the birf replacement. Great news for the trail tamer. Do they have good reviews?
 
When I switched them from side to side I filled them as recommended from guys here on mud but I could try to fill em through the fill plug. Can't hurt. Thanks for all the comments & suggestions. I will check for grooves when I tear them down for the birf replacement. Great news for the Terrain Tamer trail tamer. Do they have good reviews?
Good luck on the clean/lube fill!!

Terrain Tamer
CVs / Birfs are OE quality, quality product. The Australians have been running the for many years and we have been importing/installing them in North America for over two years - all with good results.
 
Back
Top Bottom