best gearing ???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 9, 2005
Threads
43
Messages
165
Location
Spicewood, Texas
Hi all,
New guy here been lurking awhile. I have a 76 FJ40 I bought about five years ago, wanted one all my life. It's been parked but the project is finally under way. I 'm building a rock crawler / off roader, this FJ will only see the road from a trailer. My question, What do you think the best gear ratio is to run 35" to 37" tires? I also welcome all opinions on lockers, it will be locked at both ends. I'm thinking electric locker for the front???

Thanks,
Jeff

P.S. it may help to know I'll be running the 2f (some mods) and the factory drive line.
 
Power steering, 420 or 465tranny, 3spd case or H41 and Orion, 4:88 gears...selectable locker in the front, spool/detroit/valu-lok the rear...

8274-50 up front, dual batts, high amp alt


Good luck!


-Steve
 
Thanks Steve,
Power steering is in the works as we type. I think 5:29's are avalible but heard you have to grind two teeth for install, is this correct. Farmington, I visit every November to bird hunt and snowmobile!
 
Many people run tires in excess of 38's with the stock 4.11's.
There are other ways to acheive necessary gearing more cost-effectively, namely the SM420 or 465 Steve mentioned.
Sm420-3spd case-stock 4.11's=67.1
Stock H42 4 spd-4spd case-5.29's= 37.37

Extra 30:1 with the SM420, less expensive than regearing, avoid reported strength issues with the 5.29's and gear grinding. Also nets you a good O/D running the large tires with the stock R&P.

My .02 on gearing.
 
5:29's are cool, but I have only set them up with a full float....


If you have real gearing in the trans and tcase, you should not need anything beyond 4:88's for the diffs...you are not going to be running this down the road as a DD, so you will not need to have really deep axle gears...


I ran 38's on 4:11's for a couple years..no biggie....and I run my junk down the road...


Good luck!



-Steve
 
regearing the 60 is easy...put the 4.11's from the 40 in the 60 (you'll have to swap the slip shafts from your driveshafts to mate to the pinion), then, regear the 3.70's to 4.56 and use the slip shafts from the 60 shafts since the new r & p will be fine spline anyway.
 
I run 38.5's with 5.29's. yes you do have to grind a tooth, but it is only a small corner from one tooth to get the pin to slip in. It will not hurt the overall strength of the ring gear. The pinion will twist off or an axle will break before the gears will strip if they are set up correctly.
I have a stock tranny and tcase. I would like to go to lower gears, probably an h41.
I would say that the closer to the tire you get your gearing the better because it places less torque on the rest of the drive train. Thus you can run lighter drive trian components and still have adequate strength.

If your planning a radical offroader consider an SOA with unimog portals, with cable lockers. For the price you would have gearing and lockers and bulletproof axles, plus 52" michelins are less than $200 a piece. But the diffs are on the wrong side so you'll need to use a different tcase ect. This would be my choice if I was starting form scratch and I would like to have that set up on mine combined with a GM 4.3 v6 which if placed forward would allow more room for dual cases and drive shafts (shorter than a v8)

Good luck

by the way, a stock cruiser with lockers can be fun too
 
Jetboy said:
I would say that the closer to the tire you get your gearing the better because it places less torque on the rest of the drive train. Thus you can run lighter drive trian components and still have adequate strength.



I would rather have an Atlas t-case, 3.0, 4.3, or 5.0:1 running a 4:11, than have a 5:29 or deeper at the axle...


Your point is fine, if you are using portal axles, but not for conventional Land Cruiser, Dana or anyone elses...


I would much rather beat on a 3:54 or 4:11 gear set with a big tire, having the deep gear in boxes made for it, than a 5.29 or even deeper, and increase the risk of twisting off a pinion, because of the compromise required in relation to pinion and ring gear size with deep gear sets...


Just me though...


Good luck!


-Steve
 
4.88 r/p gears. ARB front/rear. This is the setup I had when I ran my LC axles and it worked flawlessly. Never had any issues with ARB or the gears.
 
nuclearlemon said:
regearing the 60 is easy...put the 4.11's from the 40 in the 60 (you'll have to swap the slip shafts from your driveshafts to mate to the pinion), then, regear the 3.70's to 4.56 and use the slip shafts from the 60 shafts since the new r & p will be fine spline anyway.

I was actually going to post that as a question. I'm trying to go on the cheap, so i'll probably just find another 4.11 diff. (I have one in my garage)
 
Back
Top Bottom