aux. back-up lights

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

You could use something like this with a water proof cover as a disconnect. It would probably mount flush on the roof and if you sealed around it would be not leak. Only problem would be that it would be a big hole to cut out. Your lights would be really easy to disconnect.

http://www.zalytron.com/Cups.htm
 
Last edited:
I know this is going to sound cheesy, but I took one of those temporary lights with the AL sheild, one typically with the spring hand clamp, (this one has a wing nut clamp) I wired it for 12v and a lighter end, which I have a fem in the back of the 62,,,when I need it I whip it out clamp it to the hitch if doing something low, or to the rack, back or side depeinding on where I need it

and I dont have to worry about knocking it off when I am backing into trees,cause its inside!!!,, see 2k$ corner,, using the 62 as a logging tractor,,,,dragging trees

just my .02
 
I simply drilled a half inch hole in the roof a few inches forward of the rear edge, ran three wires through the hole and put a gob of quality silicone over it when the truck was a month old. At about 120,000 miles, I pulled off the silicone and re did it, but there was no evidence of it aging or other issues.

I wired a Hella FF worklamp up there with the Hella mount. The light has two 55 watt beams for tailgaters and swivel both up and down and side to side for camp use. With this model, you can pick your beam pattern. I am about to do the exact same mounting on another 80 I just bought - twins!

DougM
 
fwiw, one of the things I learned while taking my &^&%& headliner off, is that you can in fact gently pry it loose the very end of the cab and lower it by a couple of inches without too much danger of it breaking (need to remove some trim though). That would be enough to run some wires underneath in the back and make any install invisible.
Not that I would go to the trouble...
 
get a work lamp that can clip on to the hatch or something and use a jumpstart system to to run it...

My friend does that on his Tundra. Has a bright as work light that he clips to the side of the bed and runs it off his jump start system. I'm going to buy some cheapo lights that pepboys that go on the back of the hitch. Don't really need a lot of light back there but it'll get the job done and for $30 :D
 
I'm sure everyone has a different approach to things, but I like a backup light that's up high out of harm's way and where it provides better area illumination. Lights at bumper level have a way of getting broken easily in parking situations and certainly while wheeling. What I like about this setup is that the light is there always. Towing home from the lake at 11pm and hear a noise? Flick on the light and reassure yourself the boat's tied down and there's no smoke rolling off the tires. Backing out of a friend's tight driveway with rain streaming down the windows? Flick on the light and discover that black compact. There's a huge functional difference between a "part time sometimes its there and sometimes it's not" light and one that simply becomes a feature of your vehicle. I use mine at least once a month in situations you'd never think of and am an advocate of permanently mounting a quality high output light if you're going to keep yours for years. Even my wife uses it on occasion. Mine cost me $50 for the light and another $15 for the wiring and relay and switch. A portable light will rattle around inside the vehicle the 99.9% of the time you don't need it, and be too much of a hassle to get out and setup for 99% of the times you unexpectedly want to use it (see above examples).

DougM
 
Doug, I could see how a high light would provide better illumination but around here it would not be out of harms way. Trail’s here are overgrown, lots of low hanging branches (lots of matching scratches on my roof) and our new parking garage has some spots where the antenna rubs if I forget to lower it, don’t think I will be able to use if after a lift & tires
 
Crap raven, if that's the case then it doesn't sound like you will be able to fit at all with a lift and tires.

I was thinking that the light could have a swivel type mount so you could pivot it down to sort of tuck it out of the way for branches and stuff. If that's the case, those are some pretty tight trails.
 
The light will swivel down a ways if struck, but it can't get completely out of the way. In the full down position, it's lower than the factory rack side rails, in the up position it's lower than my Thule. But I agree it's vulnerable to overhead branch damage and if you've got nothing on the roof it will be the high point limiter with a lift. Mine's been wacked before in both directions and is fine. My wife takes it through the car wash a dozen times a year times 11 years with no issues.

The perfect solution would be to mount it on the top edge of the hatch above the glass. I believe it would fit fine and will examine this option when I mount one on the new 80 in a week or two. Good point.

DougM
 
I-Doug has done this - you may want to PM him.

I'm not sure he has a plug on his, but he did drill a hole in the roof. All you need is a waterproof automotive plug, which shouldn't be hard to find. I have a work light on my rack that I can remove, but it's wired with a quick disconnect throught the side window (in the process of rewiring this)

Cheers, Hugh

Hugh, I searched the Member list and found no one listed under "I-Doug". Did you mean "IdahoDoug"?
 
I think a marine connector like this would work.

10653_f.jpg
 
That is nice. Yeah, I think he means me. Mine's been up there for 170,000 miles now with a grommet full of silicone and never a leak. I redid the silicone a couple years ago just so I don't worry and found the silicone I removed still a perfect seal. It's the third one down on this page:

Recovery Gear- Hella Auxiliary Lighting, VDO Gauges


It has twin bulbs, and is available in several formats, beam widths and lenses. They are supposed to come with a swivel mount that allows the light to swivel both side to side and also up and down if struck but some unscrupulous US sellers buy them stripped and claim innocence. Look around until you find one that sells it correctly (for the same price, btw). I only found this out when I went to buy a second one about 10 years after the first in order to put it in the 2nd 80 (which I have not done yet). The light's sitting in the garage.

DougM
 
Hmm. Ironic. See the light at the top of that page has a black sheetmetal mount that lets it swivel? That's the part most sellers sell the expensive FF light without. My light is a top quality unit with expensive seals, thick glass lense, solid aluminum free form computer design dual reflectors, etc. It was designed for rough industrial applications with vibration, moisture and 100% outdoor life by Hella so it's expensive but worth it. It has been whacked by branches, parking garages, car washes and a roof box fell on it with no effect whatsoever. The twin 55w bulbs crank out some lumens. Hmmm, wonder if there's an HIR conversion for it - heh.

DougM
 
Back
Top Bottom