another no crank when hot

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 17, 2015
Threads
60
Messages
1,094
Location
Yuma, Az
I have been reading on this but couldn't find exactly what my problem is. kinda but not exactly.
since ive owned my 96 it only happened 4 times. ive read starter, read relays on the early 80 series. on july 3rd, the family and I went out into the desert to watch fireworks and my scan gauge was showing 198 before we parked. we decided to relocate with our group to the river before the show started. got in and it wouldn't start. not even a crank. all the dash lights came on just no crank. I opened the hood and popped the cover off the top of the box under the hood and the efi relay was really hot. too hot to touch. when that cooled off it started right up. it didn't sit long enough to cool the engine, only about 5 minutes.
do I need to look at something else? I havnt tried to replace the relay, I have 2 spares but forgot them at the house.
OR
maybe my LC doesn't like my wife. it only happens when shes around...

thoughts?
 
Did you tap the starter? Mine has done that a couple of times. I just give the starter a little tap with the wood handle of my hammer and good to go.
 
no. I don't see how it could be the starter. it didn't have time to cool down being attached to the engine. infact, the engine was hotter when it did fire up. 5 minutes give or take and it fired right up. I'm not saying its definitely NOT the starter, ill try it the next time it happens as well as changing the efi relay. now if it turns out being the relay, why would it get that hot?
 
I keep 2 EFI relays in my center console for this very reason EFI relay gets super hot then the truck won't start just swap it out and I am good to go some people have upgraded the wire leading to the relay and others have swapped to a relay from a Camry with success. I don't want to hack my factory wiring as that became an issue in the past on my truck and I tried the Camry relay but I got a bad relay or it just didn't work for me.
 
so your talking about the wire that operates the coil in the relay or the wires to whatever the relay controls? if its the wires to the coil that you upgrade, where do they lead? to and from. because if there is still a smaller gauge wire in that circuit, you can cause a lot more problems than the original problem. I guess I need to dig into it and see...
going from smaller to larger can cause the smaller to burn up...
 
so your talking about the wire that operates the coil in the relay or the wires to whatever the relay controls? if its the wires to the coil that you upgrade, where do they lead? to and from. because if there is still a smaller gauge wire in that circuit, you can cause a lot more problems than the original problem. I guess I need to dig into it and see...
going from smaller to larger can cause the smaller to burn up...

The wire underneath the fuse box leading to the relay I havent dug into it too much there are threads on here discussing what others have done I am really bad with wiring so I never wanted to risk it I have no problem taking the 30 seconds to swap the relay.
 
The wire underneath the fuse box leading to the relay I havent dug into it too much there are threads on here discussing what others have done I am really bad with wiring so I never wanted to risk it I have no problem taking the 30 seconds to swap the relay.
yeah I'm all about the easiest solution too. changing gauge wires can cause damage to other wires of smaller gauge. causing more headache than really needed... I would rather change an inexpensive relay over an expensive harness...
 
its hard to isolate. it doesn't do it all the time. sometimes the shotgun method of trouble shooting is the only option.

Replace the PHH.
 
No cranking = starter electrical or alarm circuit. You can crank the engine with NO EFI so that's not your problem. I would begin by inspecting the ground to the starter then re-building the starter contacts
 
Mine did this same thing the other day. Drove to a buddy's shop to work on the truck. Turned it off but needed to move it right after, and nothing. I would turn the key and I can see the battery gauge act like it sends power somewhere but no crank. I tried tapping starter, wiggling the ground wire on battery and checking relays. Nothing worked. I let everything cool and a after about 3 hrs it started right up.. Following for a solution. I'm going to check the aftermarket alarm someone put in it next.
 
ok an update. this weekend it happened twice in a day. the temps right now are in the 110+ deg range here in Yuma. my nephews and I hopped in and drove to get some burgers and when we came back out to the truck and went to start it-nothing. the engine temp was 198 when I shut it down. it started when I let it cool then proceeded to the river. when we left after swimming for a while the temps got to 205 and we stopped at a pond to have a beer. out of curiosity I went to start it and no crank. popped the hood and let it cool again and it started.
now I did disconnect the positive side on the battery for a few minutes incase it was the alarm. havent really narrowed anything down accept its doing it when its hot. now it is running hotter than normal so I need to check on that...
 
ok an update. this weekend it happened twice in a day. the temps right now are in the 110+ deg range here in Yuma. my nephews and I hopped in and drove to get some burgers and when we came back out to the truck and went to start it-nothing. the engine temp was 198 when I shut it down. it started when I let it cool then proceeded to the river. when we left after swimming for a while the temps got to 205 and we stopped at a pond to have a beer. out of curiosity I went to start it and no crank. popped the hood and let it cool again and it started.
now I did disconnect the positive side on the battery for a few minutes incase it was the alarm. havent really narrowed anything down accept its doing it when its hot. now it is running hotter than normal so I need to check on that...

mine did something similar. I started mine, drove it to a buddy's shop to work on some things. Parked it in the shop then decided to move it over a few feet to give us more room to work. Went to turn the key and got nothing. I've rebuilt the alternator, new battery, and currently rebuilding the starter.. If it happens again then i'll let you know. But I'm trying all these more "common" maintenance items for a vehicle with 312k miles first haha
 
ok an update. this weekend it happened twice in a day. the temps right now are in the 110+ deg range here in Yuma. my nephews and I hopped in and drove to get some burgers and when we came back out to the truck and went to start it-nothing. the engine temp was 198 when I shut it down. it started when I let it cool then proceeded to the river. when we left after swimming for a while the temps got to 205 and we stopped at a pond to have a beer. out of curiosity I went to start it and no crank. popped the hood and let it cool again and it started.
now I did disconnect the positive side on the battery for a few minutes incase it was the alarm. havent really narrowed anything down accept its doing it when its hot. now it is running hotter than normal so I need to check on that...
This screams starter contacts to me. If it's an OEM unit, the contacts and solenoid plunger cost around $70. Take the time to clean out the solenoid bore, because I'm sure it's all filled with dried grease and filth. Some light weight grease on the solenoid plunger is good. Make certain the new contacts are sitting flat when you tighten the copper nuts. They will want to rotate. When this happens, the contact on the plunger will not mate properly to the new side contacts.
 
Back
Top Bottom