Another Head Gasket Thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 31, 2008
Threads
47
Messages
150
Location
Boulder, CO
Ok so I'm going to replace my blown head gasket over the next week. I'm going to do it right (i.e. resurfacing & valve job). I'm just wondering if there is anything else I should do while I'm down in there.
 
Does it need it or PM? I'm in Atlanta as well and was thinking of doing mine as well. What mileage on your truck?
 
It's got 135k on it, pretty sure its blown, as there was a waterfall of coolant dripping from around the bell housing area yesterday. I tried looking at the heater hose connection this morning to see if it had ruptured, but didn't have enough time to do a really good inspection. I'm already set on doing the HG replacement even if it is the heater hose, though just a preventative measure. The odd thing is, I'm not getting any blue smoke out the tailpipe, and my temp looks fine, but coolant is pouring out at the back of the engine somewhere. I suppose the HG has blown outwards, but the portion of the HG that seals the cylinders is still intact, is that a correct assumption?
 
FYI Lawdawg, I asked a mech at Atlanta Toyota where they get their head work done. He said take it to either Lawrenceville Auto Parts or Barley's Machine Shop. Lawrenceville said they will clean and resurface the head for $75 (seems like a pretty good deal), still haven't asked about the valve job yet.
 
Ok so I'm going to replace my blown head gasket over the next week. I'm going to do it right (i.e. resurfacing & valve job). I'm just wondering if there is anything else I should do while I'm down in there.

I just finished doing mine. I would definetely replace the PHH, replace the brush in the alternator, and replace starter contact. This forum has great write ups on all of those PM's. And they are really easy to do. I would also take the time to clean the Throttle body, Upper plenum of the intake manifold as well as the lower. Mine was full of black gunk. If you're going to get the valve job done, make sure its from a reputable machine shop. Good luck. Take your time.
 
Lawdawg, disregard what I said earlier about machine shops to use, go with Will's machine shop (770)-451-4081. It was recommended by another toyota shop near me. I talked to Will and he has dealt with these heads before and knows exactly what goes into getting one done right. They are located in Chamblee.
 
And by all means, if you're getting the valve grind, take your buckets/shims/cams and let them adjust your clearances via tipping the stem ... I just learned the hard way that these dang shims are hard to come by ...
 
I suppose the HG has blown outwards, but the portion of the HG that seals the cylinders is still intact, is that a correct assumption?

This would be a relatively rare failure area on an 80. LXtreme had his fail externally at the rear of the engine but he didn't see it until he pulled the tranny for another project. It is also rare to lose that much coolant through an external HG leak.

I'm with Rick, replace the leaking hose (probably the PHH) now and plan your HG PM for a time that is convenient if you are convinced that you want to do a PM replacement.

-B-
 
10-4 just pulled off the phh this weekend, it was toast, I'm pretty sure replacing it will solve my problems. I plan to replace the HG when it gets warmer this summer as PM. Thanks for the advice, now i know what other parts to order when I replace my HG.
 
Agree it would be unlikely to have the HG push out completely on the back. The heater hoses back there would be more likely candidates. Also, when you have the head off at 140k, it would make sense to pay the extra 100 or so to have fresh valve guides put in. They come with Cdan's head gasket part kit (which also includes some things to install that you and your mechanic may not think of).

Regards,

DougM
 
Back
Top Bottom