Another A/C question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2007
Threads
15
Messages
138
Location
SoCal
I just got a 97 LC, everything was working fine, but yesterday, I was driving in bumper to bumper traffic and the A/C started to lose it's cold air. :crybaby: The temp outside was in the upper 80's and the engine temp gauge was reading normal. It seems to work fine when the temp outside is cool and when there is no traffic. Appreciate any suggestions.
 
Thanks for the tip. I read about the fan clutch and it seems that that may be the problem. But before I go through the hassle of swapping it out, does anyone have any other suggestions before I do this. Could it be just a matter of recharging the A/C?
 
Thanks for the tip. I read about the fan clutch and it seems that that may be the problem. But before I go through the hassle of swapping it out, does anyone have any other suggestions before I do this. Could it be just a matter of recharging the A/C?

Could be but how old is your fan clutch? Swapping out the fan clutch is silly simple if you don't have rusted bolts...I'm a 1 :banana: dood but after watching it being done I was like :doh:.

Take off the top fan shroud bolts, take off the 4 bolts holding on the fan clutch, slide it out between between the shroud and radiator, swap the fan itself to the new clutch, and reinstall. Took the person less than 10 minutes counting the time to grab the tools and blow off the dirt from the engine :D

I felt stupid for not doing it myself after watching it being done.
 
Cool, thanks for that tip. I'll look at it this weekend and post an update.

There are threads here on MUD how to check your existing clutch fan...But, most posts I've seen state that if your clutch fan has never been replaced then it is bad ;p

CDan (cruiserdan) here on MUD can get you an AWESOME price on the new and better blue hub clutch fan shipped to your door if you go that route. Cheap PM insurance in my mind and in my '97 it has made quite a bit of difference. It has been in the 90s here this week and driving around the LX's water temp stays right around 193-198F per my Scangauge II. Hotest I have seen it lately was 202F idling for about 15 mins in a "Fast Food" drive thru lane :rolleyes:
 
Checking fan clutch is good, but don't neglect to check your refrigerant charge also. In fact, I would do that first. Upper 80's isn't that hot relatively speaking (~113 here today). Start by checking the AC system itself, perssure on both high and low side, belts, etc. If that's all good, then move on to fan clutch.
 
I'll go ahead and check the rest of the system itself. But since I'm at 91K and it's still the original fan clutch, would it be a good idea to replace anyway for PM sake. How long do these last anyway?
 
I've got the same problem on my 95

I haven't figured out how to fix this yet. My fan clutch is good...still original but seems to have passed the checks. I had it filled with more refrigerant...but it didn't need much. I checked the coolant temperature cutoff switch and that wasn't it. My best guess (and a mechanic friend of mine) is that the expansion valve is bad. Not hard to replace but a PITA because of the hassle of evacuating the refrigerant and then replacing when you are done with the remove and replace effort.

Good luck. Let me know how you solve it.

-mt
 
I'll go ahead and check the rest of the system itself. But since I'm at 91K and it's still the original fan clutch, would it be a good idea to replace anyway for PM sake. How long do these last anyway?

IMO yes but I'm sure you'll get differing opinions. Both my rigs have just under 100K and both now have new fan clutches. I can't recall the cost for the fan clutches but IMO it was relatively cheap insurance...Order through CDan (cruiserdan) as mentioned and you'll get a good price and peace of mind that it is done.

BTW, the fan clutch does more than help with AC performance so it isn't like you are wasting money if you find out that the poor AC performance is due to something else. I did both of mind for cooling concerns and PM.
 
Replacing the fan clutch won't hurt anything, but it may not solve your problem. If you have an A/C problem, the first thing to do IMO is to check the charge. It could be as simple as checking the sight glass or hooking up a gauge set to assess hi and lo pressures. But if you don't know that you have an appropriate charge, then you're just guessing as to what the problem may be. Start with charge, then work backwards from there...
 
I had this exact problem. I futzed around with it for months & finally bit the bullet.

Expansion valve, receiver dryer, coolant flush & recharge, cleaning the 13 years of bugs, lint & dirt etc out of the heater core/fan just over 400.00 and now in the Arizona summer heat it is cooooooooool!

Just take it to a reputable AC mechanic & have it fixed is my recommendation.

Good luck.
 
I had this exact problem. I futzed around with it for months & finally bit the bullet.

Expansion valve, receiver dryer, coolant flush & recharge, cleaning the 13 years of bugs, lint & dirt etc out of the heater core/fan just over 400.00 and now in the Arizona summer heat it is cooooooooool!

Just take it to a reputable AC mechanic & have it fixed is my recommendation.

Good luck.


This is the order I've decided to try:

1. Check belts
2. Check sight glass
3. Recharge if it looks necessary and change Expansion valve
4. Change fan clutch for PM
5. Coolant flush.
6. Turn on oven, stick head in if none of that works
 
This is the order I've decided to try:

2. Check sight glass
3. Recharge if it looks necessary and change Expansion valve
4. Change fan clutch for PM
5. Coolant flush.
6. Turn on oven, stick head in if none of that works


Checking the sight glass is not an accurate way to check the fill. A fully charged 134 AC system will still show bubbles many times. The only way to properly check the charge is with proper high and low side pressure gauges (using those low side only ones that come with a can of R134 are a good way to damage your system and overcharge it).
 
Checking the sight glass is not an accurate way to check the fill. A fully charged 134 AC system will still show bubbles many times. The only way to properly check the charge is with proper high and low side pressure gauges (using those low side only ones that come with a can of R134 are a good way to damage your system and overcharge it).

When I said I futzed around with it I meant I checked the sight glass, (looked in FSM spec to my untrained eye) bought a can of freon & a cheap plastic gauge which said it was overcharged & generally wasted time/money while I was driving around being hot.

I reiterate: If I had it to do over I'd take it directly to a reputable mechanic as opposed to driving warm.
 
When I said I futzed around with it I meant I checked the sight glass, (looked in FSM spec to my untrained eye) bought a can of freon & a cheap plastic gauge which said it was overcharged & generally wasted time/money while I was driving around being hot.

I reiterate: If I had it to do over I'd take it directly to a reputable mechanic as opposed to driving warm.

BTW, love the picture of your Shepherd, I still miss mine.
 
This is the order I've decided to try:

1. Check belts
2. Check sight glass
3. Recharge if it looks necessary and change Expansion valve
4. Change fan clutch for PM
5. Coolant flush.
6. Turn on oven, stick head in if none of that works

Checking the sight glass is not an accurate way to check the fill. A fully charged 134 AC system will still show bubbles many times. The only way to properly check the charge is with proper high and low side pressure gauges (using those low side only ones that come with a can of R134 are a good way to damage your system and overcharge it).

Thanks, I'll make sure I check them carefully.

I hope you mean by #3 that you'll use a manifold gage set (you can get them relatively cheaply at harbor freight, if there's one near you) and check both high and low, and compare readings to the Factory Service Manual (or pretty much any other AC manual) and diagnose appropriately from there out of the 10 or so possibilities without defaulting to just adding refrigerant.

Are you thinking of changing the expansion valve yourself, or having someone do it? To do it correctly yourself will require more tools to evacuate your system and store the refrigerant. Overcharging can ruin your compressor and/or other parts of your AC system. Not trying to discourage you from doing it yourself, just checking that you don't do any harm to your system that might deplete your "fun" budget...

As to the fan clutch, yes its a worthwhile PM, and a new one is in the ballpark of $125-ish IIRC from CDan. However, I wouldn't just stick it in without at least changing the fluid to thicker vicosity (see threads on blue fan clutch mod) if you live in anything approaching a moderately hot climate. The out-of-the-box blue base clutch didn't help me much in AZ.
 
The question is. Is the compressor cycling on and off or is it staying on? If cycling it usually means low refrigerant but could also mean its overcharged. I just fixed this problem in my rig.. It was 101 in Murrieta the other day and the vents were ice cold.. Mine was low then I overfilled it cause I couldn't find my gauge set, then once I bled out a few psi of pressure all was good. Of course I also did all the cooling system pm stuff first and added a 14" aux fan that kicks in when the AC comes on.

You really should PM the cooling system first, then start checking the AC. The AC is designed to shut off at 226 then come back on at 217 if your rig were running slightly hot it may be contributing to the issues. Ideally find a way to monitor coolant temps through your ODBII port such as the scangauge II.
 
Back
Top Bottom