Alternator fluctuation

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

brownbear

Mod in Hibernation
Moderator
Joined
Sep 6, 2004
Threads
121
Messages
7,187
Location
Hamilton, Ontario
On my 91, the voltage seems to be low at idle(but still above the mid point). When I raise the rpms the voltage goes up to normal.

Is this a sign of a weak alternator? I know it's actually doing this as the heater fan increases with rpm.

I have had other vehicles do this before... I don't have a charge light or problems starting at all.

Just the fluctuating voltage. I have not metered it to see the changes yet. Just the looking at the not so accurate gauge.
 
Quick answer; take it to Autozone and have them put it on their tester.
First thought would be bad/loose belts or a going bad prior rebuilt alternator?

If it is Kaput, buy an OEM replacement from Cdan if you plan on keeping the rig more than a year; you won't be sorry.
 
Use a multi-meter to read the voltage at the alternator output point and at the battery at differing rpm's to see exactly what's going on. With a fifteen year old vehicle, to could simply be tired wires/cables/connections.
 
IME/O, I think it's normal. My brand-new-less-than-three-month-old OEM alternator is doing the same thing.
 
IME, it seems like the belt adjustments and condition are more important in my 3FE 62 than in my other vehicles; ie: loose or bad belts in my 62 will produce more alternator fluctuations than loose or bad belts in my 80 or other vehicles. This I noticed even when they were both younger.

I don't have much experience with a multimeter, but that does sound like the proper approach, being a tech forum and all. I might go out later and check mine, hoping I don't get a shock. I really don't like electricity.
 
Don't worry, the 12 volts on your 80 cannot shock you. The only thing that can AFAIK is the ignition coil, and that is just a little jolt.

The only thing to watch out for is shorting the large terminal on the alternator or the + terminal on the battery. The resulting arc or possible melting wires can burn you.
 
The only thing that can AFAIK is the ignition coil, and that is just a little jolt.

Grab a spark plug wire while it's running... I dare ya! ;p

Nah, it's really not that bad, it's only 20,000 volts.

Seriously though, what can you do about the low voltage at idle issue? Seems to be common among 80s, AFAIK. After a cold start, though, it charges at 14, almost 15 volts, but then drops to 13 or so after it warms up... :confused::confused:
 
On my 91, the voltage seems to be low at idle(but still above the mid point). When I raise the rpms the voltage goes up to normal

Sounds like the voltage regulator inside the alternator is going bad. If you decided to change it make sure it replaced by an OEM. Advance or Autozone alternators are junk.
 
hhmm might be normal, might be cables..

might be voltage regulator.

It may have been doing this for awhile, as I just started using the fan lots I just noticed the increases.

Belts make no squeal or real noise I have heard. And they all feel snug.
 
Small case alternators do not put out much at low RPM. The only real solution is to run an alternator with a larger case. Another option could be to overdrive the alternator but you risk over-speeding the bearings at high engine RPM.

BTW, if you go with a high output alternator of the same size case expect the problem to get worse. I have a 155 amp (bench tested) alternator built on the same Denso case as the stock alternator and it puts out about 9 amps at idle, but at 2500 engineRPM it make 155 amps.
 
Grab a spark plug wire while it's running... I dare ya! ;p

Nah, it's really not that bad, it's only 20,000 volts.

That is why I don't like getting too close to wires when they are energized; happened to me not too long ago; got the full blast from the coil wire that had a crack in the insulation; just brushed up against it. My arm hurt for awhile after that episode.

Turning belts are another issue; don't ask.

Back to the OP's question; if all above doesn't work, you could try
one of the retails stores (advance,etc) that will check out the alternator for you.

The hard part is getting the right guy who knows how to use the equipment. However, IMHO, you definitely you do not want to buy an alternator from any of those shops.

The best aftermarket warranty (and probably quality) comes from NAPA; three years on their best alternator. But, I would still go with an OEM toyota alternator if I were going to keep the vehicle for more than a year, which seems to be the average lifespan of most of the cheaper rebuilds.

g
 
Mine does the same thing. It has done it whatever alt I've put in it. The tired theory seems like a good one, but I chalk it up to "that's how it is" It's funny how much of a difference is seen between 600 and 650 rpm! In general my truck runs so much better at 650.
 
My alternator output was rock steady on my 3FE 62, until I put a rebuilt in it at 165K; then it started doing the limp willy thing. Didn't act normal until I put an OEM back in. As mentioned, the belts really have to be in good condition, properly tightened down (not loose, overstretched, or just old) and they must be OEM belts, IME
 
Back
Top Bottom