A/C Recharge

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 13, 2003
Threads
834
Messages
5,790
Location
North Front Range, CO
When I replace the dryer and line that I broke off last year, do I need to evacuate the air in the system before I charge the system with R134?
As all the R134 escaped when I hit a rock, will I need to add oil to the system too?

As exposing the dryer to the air will make the dryer not usable anymore, is there a time limit to how long the dryer can be intalled before its evacuated/filled with R134?
If I have a shop fill the R134, should I have them intall the dryer or will it be fine to drive it untill I get to the shop?
 
yes you need to get rid of the air with a vacuum pump.
there is a FSM amount of oil spec, problem is to know how much is left. Don't know how to do that without taking the whole thing apart.
I imagine it's more the water vapor that's an issue with the dryer than the air. Should be OK if you keep it plugged, I would think, but don't know that for a fact.
 
You'll need a new dryer, then evacuate the system well before refilling. If the system has been open for a while, you will probably want to flush the entire system and refill both oil and refrigerant.

If the rock caused a slow leak, you probably didn't loose much oil, so be careful not to overfill it. But if it was a rapid loss of refrigerant, then you probably need to add some. If you take it to a shop and have them refill it, they'll probably know how much to add. If you decide to do it yourself, I'd just add one of those small pressurized cans which hold 4oz I think.
 
snip

If the rock caused a slow leak, you probably didn't loose much oil, so be careful not to overfill it. But if it was a rapid loss of refrigerant, then you probably need to add some. If you take it to a shop and have them refill it, they'll probably know how much to add. If you decide to do it yourself, I'd just add one of those small pressurized cans which hold 4oz I think.


That is probably one of those things where only 1 shop in a 100 would even bother to try to add the right amount of oil. Not that they shouldn't but because it would probably take a lot of work and the customer has no way of knowing if they did it right after the fact. I'd bet they will just flat out guess and add a bit. Of course, their guess would likely be better than mine. Whether it makes a big difference on system longevity I don't know.

Note that many of the refill cans out there do contain oil. Obviously, how much is in there may or may not be what one's system needs. Also falls into the wild guesses category...

Seems to me that altogether the oil during refill thing is complete Wild West... I hope to be educated otherwise.
 
do I need to evacuate the air in the system before I charge the system with R134?

If I have a shop fill the R134, should I have them intall the dryer or will it be fine to drive it untill I get to the shop?

1. Yes

2. If I were you, Install the drier first then let the shop do the rest, otherwise they might charge you extra $ to install it.

Same as my JDM kit. I've installed it first, then have one of my buddy shop emptied out the system, and recharge the system It took about 2-1/4 lbs of 134.
AC Dryer 01.webp
AC Dryer 02.webp
AC Dryer 03.webp
 
Seems to me that altogether the oil during refill thing is complete Wild West... I hope to be educated otherwise.
Don't look to me to edumacate you :D I agree that this is a black art. Personally, I think a flush for a system that's been open for some months in is order.
 
I'd have the shop do a flush then just to be sure all the crud is out and that you're starting fresh. Then they can add the appropriate amount of oil and refrig and be done with it. JMO.
 
what do they do these flushes with?
 
It would be a safer bet to install the dryer first then flush the system. Watch out with what they charge you for the service. Usually they charge you a couple hundred dollars were in fact all the equipment, oil and freon would cost less than a hundred. I have done freon and ac conversions many times (r12 to 134), this is a simple process. As long as there are no leaks. To save cost I would have a shop just do a flush. But as around and get different qoutes, and ask what the process involves.
 
It would be a safer bet to install the dryer first then flush the system.



Huh?


You never flush the drier/accumulator, compressor, expansion device/orifice tube, or any hose that has filter or muffler.
 
What if I fill it without evac-ing it?

You could grenade your compressor because there is most likely moisture in the system and that would be bad voodoo.

110 bucks is cheap insurance. At least 134 is cheap, If I had to buy R12 it could get real spendy.
 
Back
Top Bottom