96 locker harness part numbers

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 16, 2016
Threads
16
Messages
214
Location
Signal Mountain, Tennessee
Anyone have the correct part numbers for the harness that plugs into the front and rear locking diffs?

I’ve found several threads on the forum about lockers but none defining which harness is correct.

992C6147-F1A7-4A79-B366-4FFFE2AE76DE.webp
 
If you only want a part number, any dealer website and your VIN will get you that. If you want a part, that's a different question.
 
I know your asking about a 96, and i don't know if it uses the same harness as my 94, but when i called the dealer for a replacement front locker harness i was told they were discontinued. I next called a Lexus dealer in hopes that they may of had a different part number for that same harness, no luck, they too are NLA. I ended up buying a used one from a MUD member.
 
It's not a single part # - it's 4 harnesses.

1. From firewall socket to FR locker
2. Floor harness
3. Intermediary rear harness
4. From intermediary to RR locker
 
I just went out to the shop and checked my records, the front harness running from the front locker up the inner fender is P/N 82164-60012.
 
It's not a single part # - it's 4 harnesses.

1. From firewall socket to FR locker
2. Floor harness
3. Intermediary rear harness
4. From intermediary to RR locker
Only looking for the one that plugs into the locker and runs down the axle or up to the frame. I’m making the rest.
So I would need number 1 and 4
 
Only looking for the one that plugs into the locker and runs down the axle or up to the frame. I’m making the rest.
So I would need number 1 and 4

@beno can confirm, but seems the RR pigtail (#4) is NLA, IIRC so was FR pigtail (#1)

If it helps any, LX450 floor harnesses I'm 3/3 the one I owned & 2 others checked -'97 all of them, were 'locker floor harnesses' , no matter if it was a locker rig or not. HTH.

I did the lockers like @cruiserdan , used all the OE parts & no custom pieces. If you need any Q's answered it's been a few yrs since but I am not fully senile yet.
 
I know your asking about a 96, and i don't know if it uses the same harness as my 94, but when i called the dealer for a replacement front locker harness i was told they were discontinued. I next called a Lexus dealer in hopes that they may of had a different part number for that same harness, no luck, they too are NLA. I ended up buying a used one from a MUD member.


You can use the later one for the earlier one. Your dealer box kicker would never know that.
 
You can use the later one for the earlier one. Your dealer box kicker would never know that.

^^^ This.
IIRC, the OBD rig front harness routes on the radius arm, more exposed, the OBD2 rig harness routes on the sway bar, so more protected from damage. With the needed brackets they can be interchanged, for a swap, I would always choose the later harness, 82164-60013.
 
^^^ This.
IIRC, the OBD rig front harness routes on the radius arm, more exposed, the OBD2 rig harness routes on the sway bar, so more protected from damage. With the needed brackets they can be interchanged, for a swap, I would always choose the later harness, 82164-60013.
I can confirm that the OBD locker wiring harness attaches (clamps) to the passenger side sway bar, then goes to the axle housing.
 
Last edited:
Some good info in here!
I have a simple switch in my crawler that I made and it’s always served me well. I’d like to do the same in the Cruiser with some carling switches.

Anyone have the rear part number?
 
I have searched (how I found this thread) and not found a concise part number list to add all the harnesses to convert a non-locked (91) to locked. Can anybody in this thread point me in the direction of that? Thank you. Maybe @LINUS?
 
I have searched (how I found this thread) and not found a concise part number list to add all the harnesses to convert a non-locked (91) to locked. Can anybody in this thread point me in the direction of that? Thank you. Maybe @LINUS?

Sorry amigo.

It’s been forever & 2 crashed hard drives since I did mine, pics on said drives are long gone to the dark side. Wish I could be more help.
 
Back
Top Bottom