91 octane or nothin.....

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 9, 2007
Threads
63
Messages
245
Location
FLagstaff Az. Elv.7000ft
If i dont run 91 octane my 3fe pings like crazy!
I even have the timing retarted as far as the distributer hold down bolt will allow.
Its not even hot anymore! only 75f today.......
I still have the stock gage, never has run hot or over heated,220k.
Anybody else have to run 91octane?????????
Thanks for yr input.
 
I don't know if I have to run it, but my acceleration feels a lot smoother when I need to get ahead of Miatas that drive too slow when I have it.

I'm sure 87 would work fine in mine, but I use 91 because it's only the best for my 13 year old baby.
 
In my old high mileage 22RE I had to run the expensive gas, because of carbon deposits that boosted compression and I think uneven combustion.

At any rate, that's probably you're problem. You can try cleaning out the carbon deposits with seafoam or something like that.
 
Check your emission equipment and all vac hoses and components to make sure they are connected and are not plugged up w/ carbon.
 
The 3FE was designed to run on any available fuel and if you're not in the mountains of Colorado should run just fine on 87. If your motor is pinging it is asking for help. Adjusting the AFM (which is preset from the factory and epoxy sealed) is not the correct choice IMO. Some good suggestions have been given, but I'll add one. When was the last time your fan clutch was changed? A hot running 3FE will ping like mad under medium load. The fact that the temperature gauge doesn't move means nothing as they are notoriously "lame" in the center of the range. If your ignition system, timing, emissions system, fuel delivery, intake is all up to snuff, then look to your cooling system next.
 
I always pay a little more at the pump and put in 91. Just makes me feel better not sure if it is or not but hey why not.
 
I advanced the timing on my 80 with th 3FE, and have to run super, or it will ping. Before changing the timing, it ran fine with low grade fuel.
 
I had a similar issue. I pulled my intake/TB and to replace my emissions components and I could not believe the deposits! One of my ports was over 50% clogged! After re-assembly, my pinging was mostly gone.

Good Luck!
 
Are you sure it's not your valves you hear, maybe a valve adjustiment, when was the last time you checked?

SeaFoam for cleaning the cumbustion chamber works good to...

Leave your AFM alone, more harm can be done than good.
 
Last edited:
The higher the octane rating, the slower the fuel burns. The ping noise is from "dieseling" or, ignition of the fuel/air mix without a spark - just heat and pressure. If you increase either the heat or the pressure you need to delay the fuel's combustion. This is why you need higher octane for high compression engines. Likewise, excess heat can be the cause of the dieseling.

As Jonheld has already said, checking your cooling system is good advice; however, a clogged EGR valve can also raise cylinder temps and have the same results.

Of course, it could just be your valves making noise.
 
The fan clutch is new, im wandering if i set the timing right?
when i set it i did not use the jumper wire i just set it with a light.
maybe i should check it again.
will a cooler spark plug help???
Maybe a 180 thermostat???
 
Dude,

No offence, but get a manual and save yourself from doing things more than once. If you didn't set the timing according to the FSM then the timing is wrong and nothing else you do will magically make that better.

Back to my original post, "If your motor is pinging it is asking for help."
 
You must use the "jumper wire" to adjust the timing.
That was my problem, when i did the timing last time i dint use the wire and the timing was not right.The computer will not let u adjust the timing but a few degrees , so the wire must somhow disconnect computer , so the timing can be done right.
Now all the "pinging" is gone,trucks runs great again.
Thanks for all the help.

Rob
 
Back
Top Bottom