91 landmine help!!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 30, 2008
Threads
3
Messages
14
newby here from tennessee with a 1991 landcruiser with 109,000 miles...let me give you the full story about it cause ya'll know more about these suv's than me. Back in december the radiator blew out, replaced it and everything was fine...until spring came. I noticed it running a lil warmer than usual so i took the thermostat out, still running hot and it was loosing water but none out of the tailpipe none in oil it was like it was evaporating??? Then i was going down the road and big puff of white steam came out:confused: Instantly i killed it...at the time the oil pressure was good so was the temp???

the questions are:

does anyone know where to get a good head???

is there two types of heads, my buddy runs an auto parts house and he said he would need the casting #'s and something about different intake ports???

thanks to everyone with help
 
take the head to a machine shop and have them magnaflux it and check it for warpage, both of those I'd say are un-likely but it's possible.


The head is Iron so it's durable as...
 
Are you sure its the head? If you actually need a head check the classifieds here on mud or check out the 3FE group on yahoo.

Good luck
:cheers:
 
no hose leaks found...gonna take the head off myself, first time for everything i guess, well first time for OHC at least. Timing chains:eek:
 
no hose leaks found...gonna take the head off myself, first time for everything i guess, well first time for OHC at least. Timing chains:eek:

Slow down there sonny boy, make sure you know what yer aiming at before you pull the trigger.

X2 on a cooling system pressure test before disassembly. If you think it blew into the combustion chambers, pull the plugs and check for dis-coloration of the plugs indicating water ingestion.

You can also put a boroscope into the plug holes and confirm where its leaking before digging in.

If you are lucky you will pressurize the system and find a heater hose burst and pissed water onto the exhaust manifold!!

Best wishes with your truck and let us know what you find,

Rick
 
If you are lucky you will pressurize the system and find a heater hose burst and pissed water onto the exhaust manifold!!

x - a million!!

That happened to me last year. I could have sworn up and down that the water pump was leaking, turned out it was just a hose. Whew.

Hope it's a simple fix!! :banana:
 
Head is warped...takes 4-5hrs to pull the head following the FSM. Get a valve grind kit from Cruiser Dan, along with whatever new stuff he talks you into (tell him honestly what has/has not been replaced and he will give good suggestions).

Why did you warp? Over heated one cylinder compared to the others. Pull your plugs, are they white? If so you're running too lean. Fuel Pressure Regulator, Injectors, Cold Start Injector, and Air Flow Meter need to be thoroughly checked...along with all smog stuff (AI, EGR, PCV, ALL vacuum hoses) and both air intake tubes.

Not a lean issue? Start at one end and move all the way back to it checking and replacing anything clogged/torn/cracked in your coolant system....with OEM parts...go aftermarket, and you'll be doing it twice.



BTW, the 3FE isn't OHC, just OHV...so no timing chain...just pushrods.
 
ok maybe i can't do this, cause all of ya'll went over my head so i've entrusted my friend this upcoming weekend to tear into this. I'm now leaning to the V-8 350...the motor seems just too weak(just sold my Chevy SSR:crybaby: baby on the way) and more horse power:cool:. i think i saw a good wiring diagram somewhere in here. Does anyone have this conversion?
Do you like this?
What about difference in gas mileage?
Any drive train worries?
:cheers:
 
It's only as difficult a swap as you make it. The engine mounts are available (I think), the transmission adapter is available, carb would be the simplest, FI would yield the best power/mileage...unless you wanted propane.

Re-gear....makes the 3FE so much happier. Pocket port and shave .030-.050 off the head, you'll notice the improvement in power with proper kickdown adjustment.
 
Back
Top Bottom