91 3fe overheating

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 20, 2009
Threads
5
Messages
31
Location
Bakersfield
I am at my wits end. I have pulled and inspected the waterpump ( it seemed to be new ), flushed the cooling system for about five min. and it spewed rusty water for about three of it. I also replaced the thermostat and put in a 190. after the final flush it ran cool and consistant, but during a recent trip to LA from Bakersfield ca on the first hot day of the season it got hot ( just below redline ).
So I flushed it again and once again it spewed rusty water. once it was clear I refilled with coolant and took it on a hard long run around the hills in Bakersfield on a 95 degree day and all was well it never got above half way. Then yesterday I took it to do some running around and it got hot and would not cool off unless I shut it down and let it sit . Any suggestions?:bang:
 
How are you flushing it? When you flush are you draining the block, then refilling with Toyota red and distilled water? Is your fan clutch engaging?

If you search or read the FAQ, there are hundreds of threads about running hot.
 
I flushed the radiator and the block with my hose water then filled the system with a radiator flush made by prestone to clean it out it seemed to do a good job but l was amased how much rust was in the system after the flush it was refilled was prestone antifreeze/coolant and regular old bakersfield water
the fan clutch seems to be firm when hot and loose when cool just as it should
 
Had the ame problem with my 62. Did just about everything- new waterpump, thermostat, hoses, flushed the radiator, etc. Finally, it REALLY overheated one very hot day, and cracked the head. In frustration, I took off the radiator, and found it to be almost completely plugged up; flushing wasn't enough. Got a rebuilt head, and installed a new radiator. Problem solved. I'd suggest that you need the radiator rodded out, get it rebuilt or else buy a new one. Take it off and take it to a good radiator shop, if you can find one, and see what they say. Do it before something more expensive comes along. Good luck. :cheers:Ned
 
x2 on what nodakesn3 said.

If you have rusty coolant then you probably have rust/scale in the radiator. Pull it out and check it.

Is this the original radiator? How many miles on truck? Are you mixing the coolant correctly?
 
I flushed the radiator and the block with my hose water then filled the system with a radiator flush made by prestone to clean it out it seemed to do a good job but l was amased how much rust was in the system after the flush it was refilled was prestone antifreeze/coolant and regular old bakersfield water
the fan clutch seems to be firm when hot and loose when cool just as it should

The best coolant combo is Toyota red and distilled water. Even if you remix with Prestone, USE DISTILLED WATER. Ever see how city water minerals plug up a shower head or sink? You don't want that happening to your coolant passages. After you have your radiator checked, flush, drain, then refill with the right stuff.
 
the fan clutch seems to be firm when hot and loose when cool just as it should

There is no difinitive test for the fan clutch. They have a lifespan of 100K miles or so. Replace it with OEM.
 
The best coolant combo is Toyota red and distilled water. Even if you remix with Prestone, USE DISTILLED WATER. Ever see how city water minerals plug up a shower head or sink? You don't want that happening to your coolant passages. After you have your radiator checked, flush, drain, then refill with the right stuff.

CALCIUM LIME RUST?

CLR IS A MUST!
Maybe we could try running CLR through our cooling system! It'd be a cool experiment.
 
New radiator. OEM. Everything else is just a band-aid...trust me I know. Plus a verified new waterpump, hoses, thermostat, and fan clutch are in order. Oh and a new headgasket and thorough inspection of you head by an experienced engine builder to make sure it's not warped or anything. Red coolant? Blah, can't get it anywhere if you've got an issue. Just do all new stuff, flush the block well, distilled h2o and whatever yellow/green stuff you can find everywhere not premixed. You'll never hear any fuss out of your 80 heatwise again.
 
Back
Top Bottom