850/863j combo conflicts?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 9, 2007
Threads
101
Messages
256
Location
Calgary, Canada
Hello mudders,
I've got a question for all of you running lifts.
I have been put into the position of possibly adding 863j's to the rear of my truck. Currently i am running an ome 850/860 medium combo, and have found that the rear of my truck is starting to slouch a little due to the amount of weight i am running in my truck (kaymar bumper, 35" spare, aluminumm rack, hitch mounted bike rack, and finally a drawer system).
So, if i continue to ride the 850's up front with a 1" spacer and changed the rears to the 863j's, do you all for see any issues with crazy stinkbug, or steering problems and such?
Anything i would need to change to fit these springs in the rear?
Extending brake line, etc?
Any help in this matter would be appreciated.
Cheers,
 
I'm confident that you'll need the brake line extension for the 'J's in the rear. I'm surprised you don't already have them for your 850s in the front. It makes sense to do it because if there's one thing you don't want problems with - it's your brakes. Under extreme articulation you can pop one of your original (just barely fit) lines and not even notice it until the next time you need your brakes. If your lifting suspension - extend the brake lines. My .02 :cheers:

Edit: Also, for proper wheel travel you will need to look at getting the correct shocks for your lift. If you go higher, you'll need longer travel for proper droop.
 
Last edited:
If the only issue is the sagging rear end why not just go with 863's over the J's? If you are looking for addtional overall lift that is a different.

If you go with J's in the rear and spacer up front you will most likely want to run "L" shocks. Do you have some form of caster correction? Adding the 1" front spacer will drop your caster approximately 1.74*.
 
I'm confident that you'll need the brake line extension for the 'J's in the rear. I'm surprised you don't already have them for your 850s in the front. It makes sense to do it because if there's one thing you don't want problems with - it's your brakes. Under extreme articulation you can pop one of your original (just barely fit) lines and not even notice it until the next time you need your brakes. If your lifting suspension - extend the brake lines. My .02 :cheers:

Brake lines have nothing to do with springs or lift height. The shocks determine total wheel travel, amount of droop, so it's longer shocks that need line mods.
 
Hello mudders,
I've got a question for all of you running lifts.
I have been put into the position of possibly adding 863j's to the rear of my truck. Currently i am running an ome 850/860 medium combo, and have found that the rear of my truck is starting to slouch a little due to the amount of weight i am running in my truck (kaymar bumper, 35" spare, aluminumm rack, hitch mounted bike rack, and finally a drawer system).
So, if i continue to ride the 850's up front with a 1" spacer and changed the rears to the 863j's, do you all for see any issues with crazy stinkbug, or steering problems and such?
Anything i would need to change to fit these springs in the rear?
Extending brake line, etc?
Any help in this matter would be appreciated.
Cheers,

When you carry more weight, you will probably over power the standard springs. I would go with a heaver spring rate, stiffer spring, not just taller.
 
Brake lines have nothing to do with springs or lift height.

Functionally, you are right, assuming correct shocks are on rig. He was asking, though, if brake lines should be extended. And that was my intent - to alert him to the need for longer lines on a lifted rig when installed correctly.

The shocks determine total wheel travel, amount of droop, so it's longer shocks that need line mods.

Good point, I assumed incorectly, that when a lift was installed that proper shocks would be installed also. And when proper shocks are installed for a particular lift, wheel travel is increased in the droop direction. Hopefully proper planning is done so the brake line(s) have enough slack.
 
If the only issue is the sagging rear end why not just go with 863's over the J's? If you are looking for addtional overall lift that is a different.

If you go with J's in the rear and spacer up front you will most likely want to run "L" shocks. Do you have some form of caster correction? Adding the 1" front spacer will drop your caster approximately 1.74*.

X2. 863 can handle the weight and if it is 863J, the stinkbug will be worst.
 
I ran J's and non-L shocks for a few years, and thought it was just fine. I called it a "lowrider" lift, in the sense that it's a lot of up travel and not a lot of down. When you move to L shocks then you get more down, but less up.

I say go for it if you can pick up the 863J's on the cheap, see what you think. It's not like it's hard to swap them back to what you have now, or to something else, if you change your mind. If you don't like them sell the J's to someone else. Yes you will probably want a spacer in front so it's not super stinkbug... but you only need to disconnect the lower shock bolts & e-brake cable mount above the diff and that back axle will fall low enough to pop those springs in, one hour tops to do the back.
 
Back
Top Bottom