- Location
- United States
SOLD SOLD SOLD
1971 FJ-40.
MetalTech cage.
Metaltech Tube fenders w/ inner fenders welded in.
Ford Shock towers
u-bolt front flip
Disk brake conversion front and rear (mini truck front, GM rear)
master cyl. off a mid-late 90's cruiser for 4 wheel disk.
scout II power steering conversion
Custom seat cage w/ nice buckets pulled from a late-model car.
Metaltech stinger
2" lift springs (can't remember who made them)
2" lift shackles (I don't like them, they were on the vehicle when I bought it)
rebuilt front and rear axles (seals, bearings, ect.)
4.11 gears
Aussie lockers, front and rear.
Asin Hubs
Soft top in great shape, w/ soft doors
Great shape Hard doors
Vehicle is wrapped in CamoClad camoflauge.
33" tires ( not sure on the brand, I was going to replace them but they are ok)
Engine is an "F". Runs good.
3 Speed tranny.
20 gal. extended range tank (this is the Only gas tank, as the factory doesnt fit with the aftermarket seat cage and seats)
Painless wiring harness
I have a complete 3Fe w/ computer, harness, manifolds, injectors, EVERYTHING.
I was going to rebuild the 3FE and put it in the cruiser. I started to remove the 1F and never got any further.
I have some hard top parts.
Interior has been sand blasted and rhino lined.
Jeep rear fender flairs.
Jump seats have been refinished
The bad:
the tranny need to be installed. Needs clutch.
the cage needs to be mounted.
Gas tank needs mounted and fuel lines run.
wiring needs put in.
Engine is installed, but the intake and exhaust manifolds are currently off the motor.
Brake lines need hooked up.
needs shocks.
ect. ect. ect.
It generally just needs assembled, and all the misc. stuff that goes along with that.
Here are some pictures.
The first one is what it looked like when I brought it home.
The rest are just some random pictures I put up to show some of it.
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cruiser3.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/hood 004.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cruiser 013.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cage installed 005_small.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/seat-cage 025.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/Camo 002.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/Cruiser 031.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/bedliner spray 006.jpg
I would like to get 3K out of it.
618-751-1947
ful_throttle@mchsi.com
I am located in Southern Illinois, near St louis.
1971 FJ-40.
MetalTech cage.
Metaltech Tube fenders w/ inner fenders welded in.
Ford Shock towers
u-bolt front flip
Disk brake conversion front and rear (mini truck front, GM rear)
master cyl. off a mid-late 90's cruiser for 4 wheel disk.
scout II power steering conversion
Custom seat cage w/ nice buckets pulled from a late-model car.
Metaltech stinger
2" lift springs (can't remember who made them)
2" lift shackles (I don't like them, they were on the vehicle when I bought it)
rebuilt front and rear axles (seals, bearings, ect.)
4.11 gears
Aussie lockers, front and rear.
Asin Hubs
Soft top in great shape, w/ soft doors
Great shape Hard doors
Vehicle is wrapped in CamoClad camoflauge.
33" tires ( not sure on the brand, I was going to replace them but they are ok)
Engine is an "F". Runs good.
3 Speed tranny.
20 gal. extended range tank (this is the Only gas tank, as the factory doesnt fit with the aftermarket seat cage and seats)
Painless wiring harness
I have a complete 3Fe w/ computer, harness, manifolds, injectors, EVERYTHING.
I was going to rebuild the 3FE and put it in the cruiser. I started to remove the 1F and never got any further.
I have some hard top parts.
Interior has been sand blasted and rhino lined.
Jeep rear fender flairs.
Jump seats have been refinished
The bad:
the tranny need to be installed. Needs clutch.
the cage needs to be mounted.
Gas tank needs mounted and fuel lines run.
wiring needs put in.
Engine is installed, but the intake and exhaust manifolds are currently off the motor.
Brake lines need hooked up.
needs shocks.
ect. ect. ect.
It generally just needs assembled, and all the misc. stuff that goes along with that.
Here are some pictures.
The first one is what it looked like when I brought it home.
The rest are just some random pictures I put up to show some of it.
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cruiser3.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/hood 004.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cruiser 013.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/cage installed 005_small.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/seat-cage 025.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/Camo 002.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/Cruiser 031.jpg
http://www.sonsofthefather.com/fullthrottle/ih8mud/fj-sale/bedliner spray 006.jpg
I would like to get 3K out of it.
618-751-1947
ful_throttle@mchsi.com
I am located in Southern Illinois, near St louis.
Last edited:
