7 pin mod

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

hey.
my 1994 80 is with out ABS and with out LOCKERS.
i have a CDL switch, and the plug above transfer case is unpluged.
7 pin mod will be eficient for me? and how?
i looked over the fac and couldnt fuiger out.


On NA (North American) 80s the pin 7 mod will allow manual locking of the CDL (with the CDL switch) in both Hi and Lo on transfer case. I believe you will also want to reconnect the unplugged plug above transfer case according to the instructions on the Slee site:

Slee - Pin 7 Mod for CDL (Toyota 80 Series Land Cruiser)

The 2 benefits of the pin 7 mod are that you can run the CDL unlocked in (Transfer Case) Lo and locked in Hi. By doing the mod you will determine if the CDL is locked, not the computer (also called ECU). The computer allowed
only CDL locked in Lo and unlocked in Hi before mod. Hopefully the same rules apply for your 80.

EDIT: Correction (As noted by Cj80cruiser) The only benefit of the pin 7 mod is to allow running unlocked in the Lo position of the transfer case. Thank you Cj80cruiser, to keep this technically correct!
 
Last edited:
On NA (North American) 80s the pin 7 mod will allow manual locking of the CDL (with the CDL switch) in both Hi and Lo on transfer case. I believe you will also want to reconnect the unplugged plug above transfer case according to the instructions on the Slee site:

Slee - Pin 7 Mod for CDL (Toyota 80 Series Land Cruiser)

The 2 benefits of the pin 7 mod are that you can run the CDL unlocked in (Transfer Case) Lo and locked in Hi. By doing the mod you will determine if the CDL is locked, not the computer. The computer allowed only CDL locked in Lo and unlocked in Hi before mod. Hopefully the same rules apply for your 80.

The pin 7 mod has no effect on locking the cdl in hi. You need the button to lock in hi. Pin 7 only allows you to unlock in lo.
 
The pin 7 mod has no effect on locking the cdl in hi. You need the button to lock in hi. Pin 7 only allows you to unlock in lo.


OK, technially, you're right. My mistake. But, I think the important point is that with the pin 7 mod, the driver, now, has full control of the CDL with the switch.
 
OK, technially, you're right. My mistake. But, I think the important point is that with the pin 7 mod, the driver, now, has full control of the CDL with the switch.

yeah thats true and most of what you said was but....I felt it was neccessary to make the correction since the pin 7 won't fix his ability to engage his CDL in hi....he must have the button and can use the button without the pin 7 mod to lock in hi.
 
i already have full control at CDL with the t case plug unpluged, and CDL switch button.
taking pin #7 out and plug t case back, will make a difference?

Do you know what transmission you have?

If you have an A440F (non-electronically controlled), then for you there is no advantage to changing your current set-up. On the other hand, if you have an electronically controlled A442F, then doing the "7-pin" mod and plugging the t-case sensor back in will put the low range tranny shift points back where they were originally intended to be.

Curtis
 
Pardon my ignorance, why would one want run unlocked via the 7 pin mod in low? Generally speaking, under what circumstances would this be advantageous?
 
Pardon my ignorance, why would one want run unlocked via the 7 pin mod in low? Generally speaking, under what circumstances would this be advantageous?

I personally don't plan on doing this mod but I think some do it so the truck is easier to turn when in low or to drive it on pavement in low.:confused: My experience is....I don't need it.
 
Back
Top Bottom