436,000 mi Compression Test

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Could it be that the non-DD 80s and 100s have more negative issues than DDers? It would not surprise me if that was true. What say you?

Just my experience, but my black one has been a DD since buying in '01-'02.

Blown HG, replaced starter, refreshed cooling system & EGR to fix PO401 code - the rest is oil/fluid changes, front axle service -type wrenching.

Headgasket & Starter are the only 2 days it left me walking / phoning for a ride.

2 times in 14-15 yrs, That's all the proof I need!
 
It's nice you know all this fancy stuff, but the bottom line is a simple compression test still gives the quick & dirty of the general health - sure, if one cyl was coming up dead, then go leakdown to diagnose for repairs.

But when you get these results per FSM, shows plenty to those of us who are completely content to stay with sparkplugs - we can do 2 full rebuilds & drink fancy beer for the cost of a 6BT swap! ;)

Landtoy - thanks for posting, shows what basic maint can still do towards providing a no-brainer, twist key/no problems 1FZ owner experience.

Understanding that a compression test isn't really a very valid "test" unless the same compression tester is always used, and you have a baseline established on that motor-- and the exact same circumstances in the combustion chamber are always present during the compression test isn't fancy (temperature, oil and fuel saturation, etc). This is just experience or wisdom-- whatever you prefer.

You can fetch a leak down tester from Long Acre on Amazon pretty inexpensively and learning to use it instead of a compression tester is an upgrade to any motor health test over a compression tester.

Reminds me of that expression, "Don't be limited by what you already know"....

Nevertheless, just sharing good practice. Take that advice for whatever you paid for it;)

-Phil

PS- 6BT FTW :D
 
I haven't changed the head gasket and I got it with 208,000 mi.

My oil consumption depends on rpm's. The more I rev the motor up to red line, the more oil I use. When trying M1 I would burn 1 qt per tank of gas if I ran it hard. When I got it running on the old Rotella T 5w40 (250,000 mi) I would use 1 qt first 3000 mi, then another at 2000 mi, again at 1500 etc. Just before venting to atmosphere it would use 1qt at 1800 mi and by the time I got to 6000 mi it was using 1 qt per 650 mi. I cant say exactly how much its using now as my driving habit has changed but its not consuming as much as it was before venting the crankcase to atmosphere.

My oil consumption when up at the same time I noticed that oil was seeping out the oil fill cap and PCV ports on valve cover. That was somewhere around 300,000 +/-. It was not till just a few months ago I realized it was excessive blowby. My oil was getting diluted with combustion gasses and as the oil got older/diluted it would use more oil. I have vented the crank case to the atmosphere now and consumption is down from what it was. Had I been changing the oil at 2000 to 3000 mi there wouldn't be much of an issue with blowby gasses buildup as consumption didn't get bad till the oil got about 2000 mi on it.

The one thing I see bad about using synthetic oil and extended oil changes is if your motor has excessive blowby (more than the PCV can handle) you could be doing more harm to the motor leaving all unburnt gasoline and other combustion byproducts in your motor.
 
Bought it at 208,000 mi. 3rd or 4th owner from what I could find out.
Tried several oils when I got it but found it liked Rotella T (now T6) 5w40 and Toyota filters with a 9000 mi average oil change interval for most of the time I have had it. Do some Seafoam in oil and intake every so often. Mostly use Toyota FI cleaner and BG44K in the gas. Run Shell and Conoco gas as much as possible. Change coolant with Toyota Red or other red coolant. I have not replace head gasket, no idea if the PO did.
^^^^^

I run 15W40 Rotella in everything we have. Coming up on 300,000 miles on the 80 series, original Headgasket. I use an FL1 Motorcraft oil filter though, can't see they 'toy' being that much better? Seafoam in gas occasionally.
 
With the Chevron 15w40 I have gone 4000 mi and used 4 qts. It didn't use 1 qt per 1000 mi rather it used more oil when pulling steeper hills where rpms are higher.

One thing that I dont like about the 15w40 dino oil with no oil additive (Liquid Moly Motor Oil Saver with Rotella T6) is I get a big blue cloud on most start ups, not all but most of them. The motor runs a bit rough too when cold, I assume its oil in the cylinder that is fouling the plug as it smooths out after a bit of driving. It didn't start smoking till about 3000 mi on oil. Not sure if the oil is thinning out or if the valve seals are shrinking from not having Liquid Moly Motor Oil Saver and Rotella T6 oil in it. The smoke is way less when using that combo.
 
Back
Top Bottom