4 aux lights 1 switch. Need help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 15, 2007
Threads
56
Messages
534
Location
Minneapolis, mn
I just picked up some Checker HID lights and want to set them up on the arb with the Hella's that I aready have. I already have Slee's aux light harness.

1. point me to a link explaining how to wire more than 2 light on stock toy switch?

2. or tell me how and be prepared to receive a barrage of questions?

3. Slee harness useless now?

Assume, I'm electrically stupid. Cause I am.

Thanks for the help.

ps. the lights with customer survey 25% off are $190 after tax, give or take a couple bucks.
 
From my experience: The important factor in your situation is that each pair of lights need their own relay in order to operate all the lights safely. Since all you are looking for is the ability to turn them all on with one switch I would do the following:

Wire the new lights just as you would if you were running them off of their own switch. splice them into the same wire you used to the headlight and splice the switch the remote wires (On/Off) with the existing hella wires on the back of the switch. The new lights will have their own relay, pwr, and ground wires and share the switch ground, remote lead. I hope that makes sense.
 
Will the aux toyota switch be able to handle 40 amps worth of draw?

That is how it works correct, all of the amperage in the lighting system runs through the relays and the switch?

I thought I remember someone posting something about a different way of wiring their lights so that minimal draw was going through the switch. using the switch to trip a the relays to connecting power, or something like that...

And I am cheap, thats why I own a Toyota, excuse me LEXUS... ahahaha!
 
Thanks for clearing that up. I just got off the phone with Christo and ordered another aux light harness. He said that I can tie into the switch and where the two slee light harnesses meet, sweet!!!!

That should be cool, watch out world here comes too many lights on the front of an LX.

Thanks for the help.
 
Do you want all 4 aux light on at the same time?

If so I'd just replace the relay on the Slee Aux harness with one rated high enough for all four lights. Also email Slee to see if the wire used will handle the load.

Or do you want one set to come on with the high beams and one set with the low beams?

Then I'd buy another Slee Aux harness and just wire it to the same switch. Using Configuration 1 & 2 but to your single switch on the dash.

see directions at: Slee - Light Harness


Looks like I type too slow, Christo already got you taken car of.
 
Last edited:
Both sets of lights are meant for offroad. I want them to be all accessible at one time. Is that possible with the configuration you are talking about? I guess it would be, one set wouldnt be able to turn off with the high beams but the switch would turn both off. One set is driving lights, so I guess I could run 1&2. Hmmm, I'll try that before hacking into the harness, might be cool.
 
Both sets of lights are meant for offroad. I want them to be all accessible at one time. Is that possible with the configuration you are talking about? I guess it would be, one set wouldnt be able to turn off with the high beams but the switch would turn both off. One set is driving lights, so I guess I could run 1&2. Hmmm, I'll try that before hacking into the harness, might be cool.

I don't fully understand you question/s. I described two different configurations.

I guess I should ask when do you want them on?

A. all four with high beams
B. all four with low beams
C. all four with high and/or low beams
D. Hella with low, and HID with high
E. HID with low, and Hella with high

Anything else will require another switch.
 
Back
Top Bottom