Build "3XLOCKD" build

Member Builds and Stories

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 24, 2013
Threads
87
Messages
1,155
Location
Santa Monica, CA
Figured I'd start this thread to chronicle the restoration on my newly acquired 1997 FZJ80 Moonglow Pearl. Went from a mildly built '99 Jeep XJ to an '04 100-Series, but just couldn't get excited about the Hundy. I wanted to love it, but deep down, I knew I wanted an 80-Series even more. Spent way too long looking for the right one, and this hit the mark:

- 1997 FZJ80
- Factory Locking Differentials
- 200K miles
- One Owner
- California lifetime vehicle
- Zero Rust
- Clean title
- NOT green or black

So now, the name of the game is catching up on all the PM that the previous owner neglected. He wasn't a bad guy, just not pathological about maintenance. The good thing is that these vehicles are pretty tolerant of neglect. It was just a daily driver, so not much to worry about. I bout it sight unseen.

Here's the day it was delivered:
25321938850_741193f4fd_b.jpg

25327908060_f2fd278a7a_b.jpg

25530848721_d372fd6abe_b.jpg

25019982483_1be2815bf3_b.jpg

(JDM Toilet Plunger has been replaced by new OEM struts)

A few weeks in and many, many boxes of parts. I'll start to dig in this weekend. Here's what I have in parts awaiting install:
- New EGR and VSV
- New PCV
- New Fuel Filter
- New intake manifold gasket
- New throttle body gasket
- Gates PHH upgrade
- ALL new vacuum lines
- New charcoal canister
- New distributor 0-ring
- New oil-pump seal
- Oil-pump seal torx bolt kit
- New accelerator cable
- New valve cover gasket
- New Magnaflow stainless 447103 downpipe-cat combo
- New Magnaflow stainless 447217 secondary cat
- New primary and secondary O2 sensors

Gathering parts for the axle rebuilds now. I'll tackle that with the lift install. I'll do a full tear-down and rebuild, including new 4.88 gears for my XD222 17x8.5 beadlocks with Falken Wild Peak M/T 35x12.5x17.
25825587513_810fbb026d_b.jpg

25823541854_6b18c2722e_b.jpg

26428396275_e8c3454760_b.jpg


So much to do, so little time. Way more to add, but this should be enough to get me started.

Oh, and the interior was pretty thrashed (by my wife's standards), so I decided to just start by fixing that. Katzkin Leather did a fantastic job helping me upgrade to a 40th Anniversary set of skins. Yeah, I know, some may think my priorities are backwards doing the interior before things like my first oil change, but hey, I subscribe to the "Happy Wife, Happy Life" school of thought. If she's happy, I have way more support to spend endless hours getting greasy in the garage.
26302178876_45d5018214_b.jpg

26302183106_581ede33a8_b.jpg

26328137505_37f6d1abe5_b.jpg


Let the wrenching begin. Any volunteers?
 
Not enough mods to impress us :flipoff2:
Welcome, love how clean the undercarriage is, deserves one more because of that from all of us that have salt. .. :flipoff2:
Oh, I have plans for mods. Don't you worry about that. ;) Right now, I just need to find an extra 6 or 7 hours in a day.
As for the clean undercarriage, that's the main reason it took me so long to find the right one. Having lived in Ohio and Michigan, I have no interest in chasing rust related issues.
 
Progress has been slow with work, but we're definitely pushing forward. FINALLY, my personalized plates arrived. I ordered them back in February. California DMV ain't what you would call responsive.

image.webp
 
Also tackled the intake, fuel injectors and throttle body overhaul. Did some other odds and ends while I was in there as well. Cleared all my codes and passed emissions.

image.webp


image.webp
 
Dropped off the tires to get mounted at a fantastic shop in San Dimas, LGE*CTS Motorsports. Can't say enough good stuff about this crew. Landed on a set of Falken's new Wild Peak M/T in the 35x12.5r17. Very excited to get these out on the trail. But first, I need to overhaul the axles...

image.webp
 
Midfat, That is a nice find! congrats. You gotta love rust free. When I found and bought my lx450, in 2010, I found a Vegas truck. A 1 owner truck that spent it's life in Vegas. Undereath, it looked brand new! Anyway, enjoy.
 
And while you are at it, consider running the exhaust over the frame, like the 93-94 cruisers do. It will net you quite a bit of underbody clearance.
I'll keep that in mind when I tackle the rest of the system, but that ship may have sailed given the replacement cats already installed. I was focused on clearing codes, so I went with new primary/secondary cats from MagnaFlow. Fantastic stainless system. The rest of the system is still in remarkably good shape, so I'll leave that till I have to deal with it.

image.webp


image.webp
 
To many boxes full of stuff have been sitting in the Land Cruiser for WAY to long. The past few months leading up to SEMA were kinda crazy with two seperate builds. One was an EcoBoost 2.3L in a 1972 Maverick, the other was a 2017 6.7L Super Duty rolling on 40's with a tucked long travel suspension and +6" of bulge on each fender. But now, it's back to 3XLOCKD! Home is where the heart is.

This weekend was productive. Managed to knock out a full overhaul of the driver's seat mechanism with new grease and gears. Also had both of my trashed front seat belts re-webbed through SeatBeltPlanet.com. They rock! Look and work like new.

Today started early with a long list. Managed to knock out a full suspension with the helpful hands of my 10 year old daughter. It was awesome. Eleven straight hours of wrenching with occasional breaks for ice cream, giggles, and a run to Harbor Freight for a 12 Ton press. Nothing beats time in the garage with your kids!

FINALLY installed the Icon Vehicle Dynamics 2.5" external reservoir CVC shocks along with the 3" lift springs. Dropped the front swaybar as well. Installed new castor correction bushings in the radius arms. Mounted up the 17x9 KMC beadlocks on Falken Wild Peak M/T, 35x12.5. LOVE, LOVE, LOVE the way this truck looks and drives.

Next on the list is a regear to 4.88, along with a rear axle overhaul. I'll probably farm that out as the front axle rebuild nearly cost me a new washing machine. Apparently, the wife wasn't thrilled with the Valdez-level catastrophe in the laundry room.

IMG_7658.webp


IMG_7884.webp


IMG_7869.webp


IMG_7875.webp


IMG_7885.webp
 
Last edited:
Love the build - going top quality all the way. Love the shop, too. One could eat off the floor.

I just installed the same down pipe and front CAT this weekend myself, along with a new muffler and resonator. Looks good and sounds nice, too.
 
A few more pics in the light of day. Put around 100 miles on the new lift/tires since last night. Drives so nicely. A little more side-to-side sway, but no surprise with the truck riding a few more inches Higher. I also think I need to dial in a bit more tow as it hunts a bit on the freeway.

IMG_7887.webp


IMG_7886.webp
 
Where can I find more detail on that F250?

What are you looking for? It's running Icon 3.0" external bypass CDCV on a 4-link up front and a custom Rogue Racing cantilever out back. Fenders were custom designed using OEM CAD, designed to swallow a 40" on a 17x9. Front and rear bumpers are fresh Rogue Racing designs as well. Winch is Warn Zeon 12-S. Entire grille was designed in-house and 3D printed around 6 Baja Designs S8 light bars and a set of flush mount amber S2s. Also running Baja Designs XL-Rs, and Squadrons on the rear tire rack and in the rear bumper. All lights and accessories run through an 8 channel sPOD. Turbo and ecu were massaged by aFe to 500+HP and 1050+LBFT. As good as it is on road and off, it still retains all the factory towing capability and composure. It's a beast!

IMG_0235.webp


IMG_7376.webp


IMG_7427.webp


IMG_7430.webp


524AD77C-C5A3-4DF4-A07B-3E9FC7010B13.webp
 
Back
Top Bottom