350 help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 12, 2005
Threads
287
Messages
3,081
Location
Littleton, Colorado
so my dad picked up a 40 with a 350 in it, he had it rebuilt in march. (showed us the receipts) he said it was running great, better than ever, but it just started running real real rich, and rough.

so we trailored it home yesterday and had a chance to start it, it idles great, but when youpress down the gas its just sputters and starts to die, we dont really know what were doing when we mess with the mixture screws. because weve never worked with a 350 before.

at the moment it has a quadrajet carb on it . but it came with another a seperate carb, ill have to check what it was again.

there are three adjustment screws on it, one we know is for the idle, and the others are for mixture? and something else? not sure.


guess ill have to post up some pictures of the carbs/rig.


TIA,
Max
 
Sputtering FJ

The screws you are talking about are just to adjust the idle mixture, and idle speed. If it is idling at the correct speed, and is running good and smooth at idle......don't mess with any of these screws. They do not affect "off-idle" speeds.

Make sure that your choke plate is straight up and down (when engine is hot). If the choke plate does not open up, it will run really rich and cause the conditions you describe. I don't know if you have points and condenser on this engine or not. If you do....those need to be checked before you dive into the carburetor.

Best wishes....

Don
 
accellerator pump could be bad.
dirty float bowl.
can you slowly get it to run at a higher rpm?

go get you a new fuel filter, actually there might be two, one in-line and one right where the fuel tube goes into the carb(that one could be a brass looking filter)
 
Maybe the fuel pump?

The other post about checking filters is right on. Also....maybe your fuel pump is not delivering enough gasoline for off-idle running. Can you install a gauge on the fuel line right before the carb? I would think you should see a minimum of 3-4 psig when you try to rev it up.

Don
 
yeah but very slowly.

so we took the dizzy cap off and were pretty sure that theres no points, but doesnt electronic ignition eliminate the condensor too?

so heres a picture. yeah it definetly could use a cage, and have the five point seat belts mounted safely...
IMG_0011.webp
IMG_0013.webp
 
WHAT COLOR DIST CAP? RED?
could be a mallory or something like a uni-lite set up

NICE FIND GUYS! where'd you pick that up at.

let me know if you guys want to do a cage...:grinpimp:

never mind on the color of the cap, i just relooked at the pic
 
The Distributor looks like a GM HEI. The stumble is most likely the accelerator pump in the carb, but one other place to check is the pick up coil in the distriutor. If one of the wires has a break in it, when the throttle is pushed and the port for the distributor opens on the carb, the pick up coil wires flex when the vac advance moves.

Easy way to check is pull the vac line off the distributor and plug it. If the stumble goes away it is most likely the pick up coil, if it does not go away, that is not it.

Also with the engine off and looking down into the carb from above, open and close the throttle. Does fuel spray into the throttle bores? It should spray a thin stream of fuel with a slight movement of the throttle (gas pedal or throttle shaft). If there is not a squirt of fuel into the primary (small on a q-jet) throttle bores when the gas is pushed, the accelerator pump is not working. It may be stuck down.

Steve

No sig line yet, just a 74 FJ40 in a lot of pieces.
 
aha, i have found the problem, it is indeed the accelorater pump, to get it to squirt out gas i have to push it down further than the linkage will allow it to go. so should i rebuild? or get an adapter for the other carb i have(which is a motorcraft carb BTW)

or get a different carb?

thoughts? oppinions?
 
Q-Jets are nice, I would either rebuild whatcha got or get one that is already rebuilt from Jegs or Summit..

Q-Jets give you those real small primaries which are nice for cruising around town and then the monster secondaries which are just cool
 
74fj40 said:
is there somewhere i can trade my q-jet in for a rebuilt one and get a discount?

i can see what i can do on monday for you max when i get back to work.
or i'll see if one of my techs will rebuild the one you have.

IF YOU TWO GEAR HEADS CAN WAIT! :D

or take it to a napa or carquest and see if you can get a pump, throw it in and see how it runs.
you'll only have to take the top of the carb off
 
74fj40 said:
is there somewhere i can trade my q-jet in for a rebuilt one and get a discount?
Find someone local to rebuild it. You are lucky in that you got real common stuff here and Everytown, USA has at least 10 people that can fix what you got, should you be so inclined.
 
atazman said:
Make sure that your choke plate is straight up and down (when engine is hot). If the choke plate does not open up, it will run really rich and cause the conditions you describe. I don't know if you have points and condenser on this engine or not. If you do....those need to be checked before you dive into the carburetor.

Best wishes....

Don

Not to hijack, but mine runs rich and the choke plate stays shut when hot,
Will even cause it to not start. What would cause this?
 
kdink79 said:
Not to hijack, but mine runs rich and the choke plate stays shut when hot,
Will even cause it to not start. What would cause this?

yes it will and probably why it runs rich, it's not getting enough air.

you gotta figure out why it's staying closed.
 
kdink79 said:
Not to hijack, but mine runs rich and the choke plate stays shut when hot,
Will even cause it to not start. What would cause this?
adjust your choke so it opens when hot.on the side of mine i can loosen 3 screws and turn a large round plastic cover that the spring is inside of to adjust
 
Back
Top Bottom